Installation Instructions
APPENDIX F
KWM RELAY KIT #03DAA
Appendix F-1
1998-2006 Edition
This kit contains the following parts
One Metal Bracket with Relay, Transformer & Wires mounted
Two #8 - 32nc Phil Pan Hd. self tapping screws
Two 3/16" ID x 3/8" OD Round Washers
Four (4) Blue Snap On Female Connectors
Two (2) Insulated "A" Male Connectors
Four (4) Nylon Wire Ties
One (1) Black wire extension (J2000 models only)
Tools Required
Standard Pliers Wire Stripper
Wire Connector Crimper
Wire Dikes
#2 Phillips Screw Driver bit
Electric Power drill
3/32" Flat Tip Screw Driver
1. Open both left and right side panels by removing the Phillips head screws that hold the side panels shut. Prop
side panels open.
2. Open box and identify the parts listed above.
3. See Figure 3. Identify all the wires and components that are mounted on the metal bracket. Make sure that all
wiring components are connected according to Figure 3.
4. See Figure 1. Locate the louver slot in the back panel that the Metal Bracket with relay, transformer and wires
is to be mounted in. On the J1000B, select the louver below the top most louver located above the main control
board and directly under the fuel hopper. On the J2000T and J2001T, select the louver below the top most louver
located above the Vacuum Switch (mounted on the back panel next to the left side panel).
5. Attach the Metal Bracket to the back panel using two Phillips self-tapping screws and two metal washers
(provided) as shown in Figure 2.
6. See Figure 4. Identity terminals numbered #2 and #6 on the control board and the Orange wires connected
to these terminals. Also identify the Thermostat Input block and the Red and White wires connected to it.
7. See Figure 4. Using a 3/32" (2.4mm) flat tip screw driver, loosen the screws and pull off the wires connected
to #2, and #6 terminals and the T-STAT block. If any of these wires are tied down with nylon wire ties to the stove
panel or to other wires, cut these nylon wire ties so as to free these wires. Crimp one "A" insulated male
connector (supplied) to the ends of the Orange wire you just pulled off the control board connection block.
8. Disconnect ribbon cable from ON/OFF switch by pushing in white button behind it. Trace the black wire from
terminal #7 on the control board to the ON/OFF switch mounted on the right side panel. Disconnect this black
wire from the ON/OFF switch. Connect wire to right side of Transformer.
9. Identify wire #2 in Figure 3. Connect the loose female end of this wire to the same terminal on the ON/OFF
switch as in step 8.
10. Locate the Blue Crimp ON connectors and crimp them onto wires #2 and #7 in Figure 5. Connect the male
connectors you crimped onto the ends of the Orange wires, in step 7, to these two Blue Crimp ON connectors.
Connect one Orange wire to each Blue Crimp ON connector.
11. Identify wires #5 and #6 in Figure 3. Also Locate the black and white power cord wires. Approximately 2
inches from where the power cord enters the stove compartment through the back panel, crimp one Blue Crimp
ON connector on the black and white power cord wires.
Caution
UNPLUG THE ELECTRICAL POWER SUPPLY CORD FROM THE WALL RECEPTACLE
Summary of Contents for J1000B
