background image

13 

Standby                    

Short push to turn keypad/system on. 

                                      Short push to turn keypad off. 
                                      Long push (approx. 2 sec.) to turn          

                                      system off (ALL OFF)* 

 

Down                        

Adjusts volume, bass and treble down 

                                      Adjusts balance to left and fader to       

                                      sub-woofer/amplifier 

 

IR Window               

Receives signals from remote controls 

                                      Blinks red to indicate signal received 

 

Select                        

Short push to change source* 

 

Sound

                         Long push (4 sec.) to enter Sound          

                                      Adjustment functions 

 

Up                             

Adjusts volume, bass and treble up 

                                      Adjusts balance to right and fader to    

                                      main speakers 

 

LED                            

Keypad on: Solid green 

                                      Keypad off: Off 
                                      Keypad in mute: Blinks green 
                                      Adjusting volume or sound: Blinks  or- 

                                      ange 
                                      End points on volume or sound: Blinks 

                                      red 
                                      Change source: Blinks twice for each     

                                      push 
                                      Sound adjustment functions: Blinks red 

 

*Only in Jamo enhanced A-BUS mode. See page 7.

 

Summary of Contents for KP4.6

















Reviews: