background image

e.

       

Details concerning cleaning and other maintenance

f.

 

Maintenance of water purity, especially PH values and chlorine concentrations.

g.

       

Cleaning and disinfection

h.

       

Use and installation of a cover.

i.

 

Disposal of water

j.

 

Precautions to avoid damage due to water freezing

k.

       

Precautions to avoid damage when the appliance is left empty for extended period.

     
     

2.2 Sub-clause 7

     The installation instruction shall state the substance of the following:

-

   

Earthed appliances must be permanently connected to fixed wiring;

-

   

The appliance should be supplied through a residual current device (RCD) having a rated residual 

operating current not exceeding 30 mA.

-

   

The floor has to be capable of supporting the expected load.

-

   

An adequate drainage system has to be provided to deal with overflow water.

-

   

Details of how to follow the wiring rules, for example, specifying that parts are installed in the correct zone 

and that equipotential bonding is carried out.

WAR

NING

1

DANGER

RISK OF ELECTRIC SHOCK

Connect only to a circuit protected by a

Ground Fault Circuit lnterrupter.

2

Grounding is required. The unit should be installed by a qualified service representative and

ground.

3

FOR YOUR SAFETY-This product should be installed by a professional service 

   technician,qualified in hydrotherapy bath installation.
4

lt’s prohibited to cover the instrument with something while opeating.

5

when using at the first time ,Be sure there is water in heater pipe before staring.

6

parts containing live parts, except parts upplied with safety extra-low voltage not  Exceeding

12V,must be inaccessible to person in the bath

8

earthed appliances must be permanently connected to fixed wiring

9

the appliance should be supplied through a residual current device (RCD)having a rated

residual operating current not exceeding 30 mA.

1

0 、

If  the mains cord of this appliance is damaged,It must only bereplaced  by our service

representative,As special tools and/or parts are required

Solutions of Fault

Phenomenon

Reason

How to Solve the problem

11

Summary of Contents for SPA-565
















Reviews: