background image

1

Press

 “”

 and enter Pre-heating setting mode, and the LCD flashes of “ON” 

, the “PREHEAT” icon

will flash

 , and then the circulation works on. Press

”again to

 turn off pre-heating. The LCD will show

“OFF” without flashing. 

2

) 、

Press“

minutes

and“

hours

 to adjust the time.

It will add 1 minute when pressing

  “

MIN

  each time and the minutes could be added continually.

The adjustment range is 0~59.

It will add 1 hour when pressing  

HOUR

  each time  and the hours could be added continually.  The

adjustment range is 

0-23.

After setting the heating pre-set timing, proceed to the next step.

3)

Press“

 to set the circulation times; it will show the minimum(10 minutes) on the LCD and this time

will not flash. It will add 10 minutes by pressing 

 each time.

 It will add 1 hour by pressing“

”each

time

The maximum working time is 19hours and 50 minutes.

 When you have completed this procedure continue

to the next setting.

4)

Press

 “

SET

VOL+

 again It will show “ SET” on the LCD panel. Press

 “

 button to change the setting

temperature. The range of temperature setting is: 

15~40

℃。

5)

When everything is set correctly, press the

 “

” to confirm,

 the system will quit the pre-heating setting

mode.

***Notice***

1

All setting of preheating must be in Power OFF mode, just turn on the spa

the

LCD will display “---”

2

Please note that it shows "on" or "off" on the LCD.  "on" means preheating is

turned  on  mode.  when the time  of  pre-heating  is  as  same as  current time, the
heater will start working. "off" means the heater won’t start to work an any time.

3

Circulation PUMP and HEATER without working while setting preheating.

6

Operation of 

preheating

When the preheating time is as same as the current time, the LCD screen shows “on” and the tub is also

filled   with   water.   The   heater   will   start   to   work.   The   heater,   circulation   pump   and   time   counting   work   at

simultaneity. The countdown time will be shown on the LCD screen, till the preset time is finished.

During the preheating, The preheating will be turned off automatically once the preset time is finished. 

7

Summary of Contents for SPA-565
















Reviews: