background image

MODEL 220 

HYDRAULIC 

IMPACT HAMMER 

IV. 

MAINTENANCE AND ADJUSTMENTS 

 
 

S.  CHECKING & REPLACING RECOIL DAMPENER 

 

The thickness of a new recoil dampener with hammer weight on dampener is 1 
1/2"(38mm).  If the thickness is less than 1 1/4"(32mm), the dampener should be 
replaced. 

 

To replace recoil dampener:  Loosen wire rope holding drive cap to hammer.  Pick 
up hammer to allow old dampener to be removed.  Replace with new dampener.  
Re-tighten clamps on wire rope.  Wire rope should be adjusted so that with hammer 
lifted 1-2"(25-50mm) gap exists between recoil dampener and hammer base plate 
(160451). 

 

See FIG 3, Page II-7, for location of recoil dampener 

 
 

T.  CHECKING & REPLACING CUSHION MATERIAL 

 

With new cushion material, the striker plate flange should be 2" (45mm) above the 
top of a DCB-1 Drive Cap (32" leads).  If this dimension is reduced by more than 
1/2"(13mm), replace the cushion material. 

 

See Section II F Page II-6 ATTACHMENT OF DRIVECAP for instructions on 
replacing cushion material. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

IV-15 

 

Summary of Contents for 220

















































































Reviews: