background image

H031

1300A

 6000 Condor Drive • Moorpark, CA USA 93021  •  800.822.7933  •  Fax 877.327.1403

Zodiac Pool Systems, Inc.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This warranty is limited to the first retail purchaser, is not transferable, and does not apply to products that 
have been moved from their original installation sites. The liability of Zodiac Pool Systems, Inc. shall not 
exceed the repair or replacement of defective parts and does not include any costs for labor to remove 
and reinstall the defective part, transportation to or from the factory, or any other materials required to make 
the repair. Refrigerant or other expendables are not covered by the warranty. This warranty does not cover 
failures or malfunctions resulting from the following:

LIMITED WARRANTY

• AquaLink

®  

RS units installed with Jandy

®

 Surge Protection Kits will be covered for two (2) years.

• Never Lube

®  

valves are warranted for the life of the pool and/or spa on which they were originally installed.

• AquaPure

®  

Electronic Chlorine Generator Electrolytic Cells carry a five (5) year limited warranty on a prorated basis.

• Heat pumps are covered for two (2) years. There is a lifetime warranty on titanium tubing.
• The heat pump compressor is covered for five (5) years. 

1. Failure to properly install, operate, or maintain the product(s) in accordance with our pubished Installation,
    Operation and Maintenance Manuals, which are provided with the product(s).
2. The workmanship of any installer of the product(s).
3. Not maintaining a proper chemical balance in your pool and/or spa [pH levels between 7.2 and 7.8, with 
    ideal ranges being between 7.4 and 7.6, Total Alkalinity (TA) between 80 to 120 ppm, 
    Total Dissolved Solids (TDS) less than 2000, not including salt ppm].
4. Abuse, alteration, accident, fire, flood, lightning, rodents, insects, negligence, or acts of God.
5. Scaling, freezing, or other conditions causing inadequate water circulation.
6. Operating the product(s) at water flow rates outside the published minimum and maximum specifications.
7. Use of non-factory authorized parts or accessories in conjunction with the product(s).
8. Chemical contamination of combustion air or improper use of sanitizing chemicals, such as introducing
    sanitizing chemicals upstream of the heater and cleaner hose or through the skimmer.
9. Overheating; incorrect wire runs; improper electrical supply; collateral damage caused by failure of O-rings, 
    DE grids, or cartridge elements; or damage caused by running the pump with insufficient quantities of water.  

LIMITATION OF LIABILITY:

This is the only warranty given by Zodiac Pool Systems, Inc. No one is authorized to make any other warranties 
on behalf of Zodiac Pool Systems, Inc. 

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, 

EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF FITNESS 
FOR A PARTICULAR PURPOSE AND MERCHANTABILITY. ZODIAC POOL SYSTEMS, INC. EXPRESSLY 
DISCLAIMS AND EXCLUDES ANY LIABILITY FOR CONSEQUENTIAL, INCIDENTAL, INDIRECT, OR 
PUNITIVE DAMAGES FOR BREACH OF ANY EXPRESSED OR IMPLIED WARRANTY.

 This warranty 

gives you specific legal rights. You may also have other rights that vary by state or province. 

WARRANTY CLAIMS:

For prompt warranty consideration, contact your dealer and provide the following information: proof of purchase, 
model number, serial number, and date of installation. The installer will contact the factory to obtain instructions 
regarding the claim and to determine the location of the nearest designated service center. If the dealer is not 
available, you can locate a service center in your area by visiting www.jandy.com or by calling our technical 
support department at 1.800.822.7933. All returned parts must have a Returned Material Authorization number 
to be evaluated under the terms of this warranty. 

Thank you for purchasing Jandy

®

 pool and spa products. Zodiac Pool Systems, Inc. warrants all parts to be 

free from manufacturing defects in materials and workmanship for a period of one (1) year from the date of 
retail purchase, with the following exceptions:

Litho in U.S.A. © Zodiac Pool Systems, Inc. 0810

Summary of Contents for ePump

















Reviews: