Jandy Legacy LRZM, Installation And Operation Manual

Page 23

Legacy

™

 Model LRZM Pool/Spa Heater Installation and Operation Manual

 CAUTION

Do not attempt repairs on the gas controls or appli-
ance. Tampering is dangerous and voids all warran-
ties.

 ATTENTION

Ne tentez pas d’effectuer des réparations au sys-
tème de régulation du débit du gaz ou à l’appareil. 
Toute modi

fi

 cation non autorisée est dangereuse et 

entraîne l’annulation de toutes les garanties.

 CAUTION

Keep all objects off the top of the heater. Blocking 
air 

fl

 ow could damage the heater, and may void the 

warranty.

 ATTENTION

Ne posez aucun objet sur le dessus de l’appareil. 
Il pourrait empêcher la circulation de l’air, ce qui 
risquerait d’endommager l’appareil et d’annuler la 
garantie.

 WARNING

Vent pipes, draft hoods, and heater tops get hot! 
These surfaces can cause serious burns. Do not 
touch these surfaces while the heater is in opera-
tion. Adding a vent cap reduces the temperature on 
the top.

 AVERTISSEMENT

Les tuyaux d’aération et le dessus de l’appareil 
deviennent chauds! Ils peuvent causer de graves 
brûlures. Ne touchez pas à ces surfaces lorsque 
l’appareil est en marche. 

 WARNING

For your safety, when starting the heater, keep your 
head and face well away from the lower 

fi

 rebox 

opening to prevent any risk of personal injury.

 AVERTISSEMENT

Pour votre sécurité personnelle lorsque vous mettez 
l’appareil en marche, tenez votre tête et votre vis-
age loin du brûleur pour éviter tout risque de bles-
sure.

Be sure that there is water in the pool and that the 

surface level is above the skimmer or other inlet of the 

pool’s 

fi

 lter system.

Con

fi

 rm that pool water is 

fl

 owing normally 

through the pool system and equipment.  With any new 

pool or spa installation, operate the 

fi

 lter pump with 

the heater off long enough to completely clean the 

water. This will remove any installation residue from 

the water. Clean the 

fi

 lter at the end of this operation 

before starting the heater.  Start the heater in accor-

dance with the Operating Instructions section of this 

manual, with particular attention to the lighting and 

shutdown instructions and temperature control opera-

tion. 

Section 7.  Operating Instructions

7.1 Normal 

Operation

The Legacy model LRZ millivolt heaters are 

capable of automatic operation based on a call for 

heat at a preset temperature. The heater has an inter-

nal safety system which allows operation in a variety 

of conditions and prevents operation when certain 

adverse conditions are encountered. 

When the heater's pilot is lit and the pilot 

generator is providing a millivolt signal to the safety 

circuit, water is 

fl

 owing through the heater, and the 

temperature of the water entering the heater is below 

the temperature control setting, an operating cycle is 

initiated by the automatic control. The temperature 

control circuit is closed, activating the gas valve and 

the gas valve is opened. Gas 

fl

 ows through the burners, 

is mixed with air in the combustion chamber, and is 

ignited by the pilot.  Operation will continue until the 

temperature of the water entering the heater reaches 

the temperature control setting. 

If ignition is unsuccessful, or if the 

fl

 ame fails 

during normal operation, the temperature control 

circuit opens and shuts off the gas valve.

7.2 Start-Up

 CAUTION

Do not use this heater if any part has been under 
water. Immediately call a quali

fi

 ed service techni-

cian to inspect the heater and replace any part of 
the control system and any gas control which has 
been under water.

 ATTENTION

N'utilisez pas cet appareil s'il a été plongé dans 
l'eau, même partiellement. Faites inspecter 
l'appareil par un technicien quali

fi

 é et remplacez 

toute partie du système de contrôle et toute com-
mande qui ont été plongés dans l'eau.

 CAUTION

Should overheating occur or the gas supply fail to 
shut off, turn off the manual gas control valve to the 
heater.

 ATTENTION

En cas de surchauffe ou si l'alimentation en gaz ne 
s'arrête pas, fermez manuellement le robinet d'arrêt 
de l'admission de gaz.