background image

Janfire

pelletswärme

 Janfire 06.2011

of high quality isolation material is used to prevent thermal lost. Powder coated sheets are used for 

the cover panel. Cast iron is used for the grill and the handholds.

 

The connectors for flue gas, thermal relief valve and the water supply are on the backside of the 

Combiflame. The boiler can be placed on 4 adjustable feet. 

The Combiflame will be delivered including the catalytic converter, the Janfire pellet burner NH and 

this manual.

Purchased parts package :

• Boiler Combiflame including the catalytic converter

• four adjustable feet

• ash pit

• grill for operation with log

• pellet burner NH

• thermal controller for the draft flap (only used for operation with log)

• manual

• muffles

!

This manual is part of the boiler. It is only legal for the Janfire Combiflame 

pellet boiler. It contains useful informations for safe operation, handling and 

maintenance. This manual has to be kept close to the boiler and it has to be 

on hand anytime of operation. Local terms have to be followed. 

135

702

893

23

11

7

8

10

17

15

16

9

14

12

25

920

132

132

890

18

19

20

21

22

23

24

1169

479

1

2

3

4

5

25

27

26

28

Summary of Contents for Combiflame






















Reviews: