background image

3

 

PROBLEM 

 CAUSE   

   REMEDY 

        REFERENCE 

   6.  Noisy 

1.  Backlash between shuttle hook   See mechanical adjustment  

P. 14

     operation 

  gear and lower shaft gear is  

 “Clearance between needle and

     

  too great. 

 hook (NO. 2).”

   

  

     

2.  Lower shaft gear is loose. 

 Eliminate the looseness. 

   

  

     

3.  Inappropriate belt tension.   

 See mechanical adjustment  

P. 22

     

   

 “Motor belt tension.”

   

  

 

     

4. Upper shaft gear is loose.  

 Eliminate the looseness.

     

5.  Not enough oil.  

 Oil all moving parts. 

  7.  Deformation of  1.  Inappropriate zigzag  

 See mechanical adjustment  

P. 11

    pattern   

  synchronization. 

 “Needle swing.” 

   

  

 

     

2.  Inappropriate disengagement 

 See mechanical adjustment  

P. 21

     

  of cam follower.  

 “disengagement of cam follower.”

   

  

   

  

 

     

3.  Upper thread tension is too  

 Adjust upper thread tension  

P. 8

   

 strong. 

 

correctly.

    
     

4.  Inappropriate feed balance  

 See mechanical adjustment  

P. 19

     

  BALANCE 

 "Feed balance on stretch stitch."

   

  

 

  

Summary of Contents for 13512


























Reviews: