background image

19

NOTE:

* When you thread the upper looper only, to avoid

tangled threads pull out both threads over the
needle plate and under the presser foot.

Turn the handwheel toward you until the upper
looper comes to the middle point of its travel, and
unhook the thread of the lower looper from the
upper looper.
Thread the upper looper.

1

Lower looper thread

2

Upper looper

4. Insert the thread between tension discs from the

right. Then pull both sides of thread.

5. Pass the thread through upper looper thread

guide (1)

4

Upper looper thread tension dial

5

Upper looper thread guide (1)

6. Pass the thread through upper looper thread

guide (2).

7. Pass the thread through the looper thread

take-up lever (upper).

6

Upper looper thread guide (2)

7

Looper thread take-up lever (upper)

8. Pass the thread through upper looper thread

guide (3).

9. Holding the end of the thread with a pair of

tweezers, pass it through the hole on the upper
looper. Pull 10 cm (4˝) or more of thread through
the hole.

8

Upper looper thread guide (3)

9

Upper looper

5

4

6

7

8

9

1

2

4  5

6  7

8  9

Summary of Contents for 8002DG











































Reviews: