background image

21

Mechanical Adjustment

MODEL: AirThread 2000D

To check:
1.  Open the looper cover and the side cover.
2.  While pressing the upper knife release knob, turn it 

clockwise by half a rotation to deactivate the upper 
knife.

3.  Remove the left needle.
4.  Attach an HAx1 SP #11 needle as the right needle.
5.  Turn the handwheel toward you until the tip of the 

lower looper comes from the left to the rear groove of 
the right needle.

    Check if the clearance between the rear groove of the 

right needle and the tip of the lower looper is 0 to 0.05 
mm when the needle and the lower looper intersect.

7.   Attach an HAx1 SP #11 needle as the left needle.
8.  Check if the clearance between the rear groove of the 

left needle and the tip of the lower looper is 0 to 0.05 
mm when the needle and the lower looper intersect.

    If not, adjust as follows.

To adjust the clearance between the needle and the 
lower looper
1.  Open the looper cover (unit) and the side cover (unit).
2.  While pressing the upper knife release knob, turn it 

clockwise by half a rotation to deactivate the upper 
knife.

3.  Remove the presser foot (unit).
4.  Remove the needle plate.
5.  Remove the left needle.
6.  Attach an HAx1 SP #11 needle as the right needle.
7.   Turn the handwheel toward you until the tip of the 

lower looper comes from the left to the rear groove of 
the right needle.

8.  Check if the clearance between the rear groove of the 

right needle and the tip of the lower looper is 0 to 0.05 
mm when the needle and the lower looper intersect.

NOTE: 
If the needle guard (front) pushes the front surface of the 
needle, temporarilly move the needle guard (front) to the 
front.
9.  Loosen the bolt slightly. Adjust the clearance by 

moving the lower looper base. After adjustment, 
tighten the bolt.

NOTE: 
During adjustment, make sure that the lower looper base 
does not turn or the handwheel does not rotate.  
Otherwise, the timing of the needle and the lower looper 
will be wrong.

10. Attach an HAx1 SP #11 needle as the left needle.
11. Turn the handwheel toward you until the tip of the 

lower looper comes from the left to the rear groove of 
the left needle.

The standard clearance between the groove of the needle (HAx1 SP #14) and the tip of the lower looper is 0 to 0.05 
mm when the needle and the lower looper intersect.

Upper knife release knob

Upper knife

Bolt

Setscrew B

Needle bar gauge

Needle 
guard (front)

Lower looper

Needle bar gauge

Setscrew A

Needle bar lower bushing

Thumbscrew

Groove

Needle 
guard (rear)

0.05 - 0.25mm

0 - 0.05mm

To adjust the clearance of the needle and the lower looper; and the clearance 

of the needle and the needle guard (front) (1)

Needle bar gauge

Needle bar

Bolt

Summary of Contents for AirThread 2000D














































Reviews: