Janome Magnolia 7034D Instruction Book Download

Page: 2 / 42

IMPORTANT SAFETY

INSTRUCTIONS

Your sewing machine is designed and constructed only for HOUSEHOLD use.

Read all Instructions before using this appliance.

DANGER

–

To reduce the risk of electric shock:

An appliance should never be left unattended when plugged in. Always unplug this appliance from the

electrical outlet immediately after using and before cleaning.

Always unplug before relamping. Replace bulb with same type rated 15 Watts.

Do not reach for the appliance that has fallen into water. Unplug immediately.

Do not place or store appliance where it can fall or be pulled into a tub or sink. Do not place in or drop

into water or other liquid.

WARNING

–

To reduce the risk of burns, fire, electric shock,or injury to persons.

Do not allow to be used as a toy. Close attention is necessary when this appliance is used by or near

children.

Use this appliance only for its intended use as described in this manual.

Use only attachments recommended by the manufacturer as contained in this manual.

Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been

dropped or damaged, or dropped into water. Return the appliance to the nearest authorized dealer or

service center for examination, repair, electrical or mechanical adjustment.

4. Never operate the appliance with any air opening blocked. Keep ventilation openings of the sewing

machine and foot controller free from accumulation of lint, dust, and loose cloth.

5. Never drop or insert any object into any opening.

6. Do not use outdoors.

7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

8. To disconnect, turn all controls to the off (“ 0 ”) position, then remove plug from outlet.

9. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

10. Keep fingers away from all moving parts. Special care is required around the sewing machine needle

and knives.

11. Always use the proper needle plate. The wrong plate can cause the needle to break.

12. Do not use bent needles.

13. Do not pull or push fabric while stitching. It may deflect the needle causing it to break.

14. Switch the sewing machine off (“ 0 ”) when making any adjustment in the needle area, such as

threading needle, changing needle, threading loopers, or changing presser foot, and the like.

15. Always unplug the sewing machine from the electrical outlet when removing covers, lubricating, or

when making any other adjustments mentioned in the instruction manual.

SAVE THESE INSTRUCTIONS

Summary of Contents for Magnolia 7034D











































Search results

Summary of Contents for Magnolia 7034D

Reviews:

Related manuals for Magnolia 7034D

Brands by name

Popular brands

Janome Magnolia 7034D, Instruction Book

Search results

Summary of Contents for Magnolia 7034D

Reviews:

Related manuals for Magnolia 7034D

Brands by name

Popular brands