background image

56 

 

56

 

10.3  

GENERAL 

REPORTS 

 
    A            (Report Code)                Total 1 (Cash) 

 

KEY 

  A   

:      "X" mode for reading report, "Z" mode for deleting report 

Report Code   

:      see below table 

10.3.1 TABLE 1 - Daily and P-T-D reports in numeric format 
CODE   REPORT TYPE 

 X 

 Z 

  Daily full terminal report 

  yes 

yes1 

  Personal report N. 1 

  yes 

  yes 

  Personal report N. 2 

  yes 

  yes 

  Personal report N. 3 

  yes 

  yes 

  Personal report N. 4 

  yes 

  yes 

10 

 Daily Departments 

 yes 

 yes1 

11 

  Daily Departments. for groups (GROUP 1) 

  yes 

  no 

12 

  Daily Departments. for groups (GROUP 2) 

  yes 

  No 

13 

  Daily Departments. for groups (GROUP 3) 

  Yes 

  No 

14 

  Daily Departments. for groups (GROUP 4)   

  Yes 

  No 

15 

  Daily Departments. for groups (DETAILED) 

  Yes 

  No 

16 

  Daily Departments. for groups (All the Groups)  

 yes  

 No 

20 

 PLU Selling data 

 yes 

 yes 

21 

  Top 25 PLU amount 

  yes 

  no 

22 

  Top 25 PLU quantity 

  yes 

  no 

30 

 Daily transaction  

 yes 

 no1 

31 

 Daily VAT 

 yes  

 no 1 

33 

 Cash  in Drawer 

 yes 

 no 

40 

  Daily Clerks (total embedded amount) 

  yes 

  yes 

42 

  Clerks secret codes reset 

 No 

 yes 

50 

 Daily hourly 

 yes 

 yes 

60 

 Daily PB situation  

 yes 

 yes 

61 

 Daily PB movements  

 yes 

yes 

62 

 Daily Invoices/Bills 

 yes 

yes 

101 

  P-T-D Full Terminal Report 

  yes 

yes 

110 

 P-T-D Departments  

yes 

yes 

111 

  P-T-D Departments. for groups (GROUP 1)   

yes 

no 

112 

  P-T-D Departments. for groups (GROUP 2)   

yes   

no 

113 

  P-T-D Departments. for groups (GROUP 3)   

yes   

no 

114 

  P-T-D Departments. for groups (GROUP 4)   

yes   

no 

115 

  P-T-D Departments. for groups (DETAILED)   

yes   

no 

116 

  P-T-D Departments. for groups (All the Groups)   

yes   

no 

120 

  P-T-D PLU selling data 

yes  

yes 

121 

P-T-D Top 25 PLU amount   

Yes No 

122 

  P-T-D Top 25 PLU quantity 

yes No 

124 

PLU STOCK situation 

yes Yes 

 

 

 

 

130 

 P-T-D Transaction  

yes  

yes2 

 

 

 

 

131 

 P-T-D VAT  

yes  

no2 

140 

  P-T-D Clerks (total embedded amount)   

yes   

yes 

150 

 P-T-D hourly  

yes  

yes 

161 

 P-T-D PB movements  

yes  

yes 

162 

 P-T-D Invoices/Bills  

yes  

yes 

 

 

Summary of Contents for J3500E




























































































































Reviews: