Se
Se
tti
tti
ng Format f
ng Format f
or Depth Da
or Depth Da
ta O
ta O
utp
utp
ut
ut
DEPTH
DEPTH
Ver1.5
Ver1.5
Ver2.3
Ver2.3
AL
AL L
L
Display the
Display the window shown
window shown above.
above. The format
The format changes each
changes each time you
time you press the
press the up or
up or
downward-arrow
downward-arrow key
key..
Notes:
Notes:
1. There are three output formats: NMEA0183V2.3, NMEA0183V1.5, or ALL.
1. There are three output formats: NMEA0183V2.3, NMEA0183V1.5, or ALL.
2. In the case of NMEA0183V2.3, only "SDDPT" sentences are output.
2. In the case of NMEA0183V2.3, only "SDDPT" sentences are output.
$SDDPT
$SDDPT, xxx.x, x.x,
, xxx.x, x.x, x.x *hh (CR)(LF)
x.x *hh (CR)(LF)
(1)
(1) (2)
(2) (3)
(3) (4)
(4)
(1) Depth measured from the transducer regardless of the depth display mode setting (in
(1) Depth measured from the transducer regardless of the depth display mode setting (in
meters
meters only
only.)
.)
(2) According to the depth display mode:
(2) According to the depth display mode:
DISP-SURF: Draft value (no + or – sign preceding values)
DISP-SURF: Draft value (no + or – sign preceding values)
DISP-TRANS: 0.0
DISP-TRANS: 0.0
DISP-KEEL: Keel height compensation (– sign preceding values)
DISP-KEEL: Keel height compensation (– sign preceding values)
(3) Measuring range: RANGE (in meters only)
(3) Measuring range: RANGE (in meters only)
(4) Checksum (result after each ASCII code of every character between "S" just after "$" and
(4) Checksum (result after each ASCII code of every character between "S" just after "$" and
"X" just before " * " is EXORed.)
"X" just before " * " is EXORed.)
3. In the case of NMEA0183V1.5, the output sentence varies according to the depth display
3. In the case of NMEA0183V1.5, the output sentence varies according to the depth display
mode setting.
mode setting.
• When DISP-SURF is set, only the "SDDBS" sentence is output.
• When DISP-SURF is set, only the "SDDBS" sentence is output.
$SDDBS, xxx.x, f, xxx.x, M, xxx.x, F(CR)(LF)
$SDDBS, xxx.x, f, xxx.x, M, xxx.x, F(CR)(LF)
(1)
(1)
(2)
(2)
(3)
(3)
• When DISP-TRANS is set, only the "SDDBT" sentence is output.
• When DISP-TRANS is set, only the "SDDBT" sentence is output.
$SDDBT
$SDDBT, xxx.x, f,
, xxx.x, f, xxx.x, M, xxx.x, F(CR)(LF)
xxx.x, M, xxx.x, F(CR)(LF)
(1)
(1)
(2)
(2)
(3)
(3)
• When DISP-KEEL is set, only the "SDDBK" sentence is output.
• When DISP-KEEL is set, only the "SDDBK" sentence is output.
$SDDBK, xxx.x, f, xxx.x, M, xxx.x, F(CR)(LF)
$SDDBK, xxx.x, f, xxx.x, M, xxx.x, F(CR)(LF)
(1)
(1)
(2)
(2)
(3)
(3)
The field values are the same in each of the three sentence types:
The field values are the same in each of the three sentence types:
(1) Depth value after compensation (in feet)
(1) Depth value after compensation (in feet)
(2) Depth value after compensation (in meters)
(2) Depth value after compensation (in meters)
(3) Depth value after compensation (in fathoms)
(3) Depth value after compensation (in fathoms)
(4) No check sum
(4) No check sum
4.
4. Operation
Operation 21
21
Summary of Contents for JFE-680
