background image

MODEL # DA333BC- MADISON SINGLE 

CRIB (NATURAL)

*
*
*

*

*

*

*
*

*

*
*

*

*
*
*

*
*

Follow warnings on all products in a crib.

*
*

*
*

Customer Service Department No. 413

12345 Albert-Hudon Boulevard, Suite 100

Montreal, Quebec

Canada H1G 3L1

CUSTOMER SERVICE    

If you are missing parts or have any questions about this product, contact our customer service representative first!

CALL 1-800-295-1980      

You can also order parts by writing to the address listed below.  Please include the product model number, color 
and a detailed description of the part.

Before each usage or assembly, inspect crib for damaged hardware, loose joints, missing parts or 
sharp edges, 

DO NOT

 use crib if any parts are missing or broken.  Ask your dealer or write to our 

customer service representative (address & phone number shown above) for replacement parts and 
instructional literature if needed.  

DO NOT

 substitute parts.

Infants can suffocate on soft bedding.  Never add a pillow or comforter.  Never place additional 
padding under an infant.

When child is able to climb out or reaches the height of 35 inches (90 cm), the crib shall no longer be 
used.
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, 
unless otherwise advised by your physician.

E-MAIL: csr@jardcoent.com

WARNING              

Failure to follow these warnings and assembly instructions could result in serious injury or death.
Read all instructions before assembling crib.  

KEEP INSTRUCTIONS FOR FUTURE USE.

When child is able to pull to standing position, set mattress to lowest position and remove bumper 
pads, large toys and other objects that could serve as steps for climbing out.
Never use plastic shipping bags or other plastic film as mattress covers because they can cause 
suffocation.
DO NOT use a water mattress with this crib.
Replace teething rail if damaged or loose (if teething rail is provided for this model).

DO NOT place crib near window where cords from blinds or drapes may strangle a child.

Strings can cause strangulation!  

DO NOT

 place crib with a string around a child's neck, such as hood 

strings or pacifier cords.  

DO NOT 

suspend strings over a crib or attach strings to toys.

To help prevent strangulation tighten all fasteners.  A child can trap parts of the body or clothing on 
loose fasteners.
If refinishing, use a non-toxic finish specified for children's products.

Assemble on soft, smooth surface to prevent damage to product finish.

Phillips head screw driver is not included.

DO NOT use power tools.

CAUTION:  ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27-1/4 INCHES BY 51-5/8 
INCHES (69CM BY 131CM) WITH A MINIMUM THICKNESS OF 4 INCHES (10CM) BUT NOT 
EXCEEDING 6 INCHES (15CM).

Infants can suffocate in gaps between crib sides and a mattress that is too small.

NOTES

Ensure all parts and components are present before beginning assembly.

Summary of Contents for MADISON DA333BC








Reviews: