background image

 

22

AIR CIRCULATION OF THE HEATING SYSTEM 

Always refer to the applicable building code before installing the hot air conduct. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
It is recommended to install a floor trap in order to balance the air pressure between the 
floor where the appliance is installed and the superior floor.  
 
It is also recommended to install those floor traps at each room extremity. 
 
An air supply must be installed if : 

a)  The  appliance  seems  to  have  an  irregular  draft  control,  a  smoke  return,  a  bad 

combustion and a counter-blow even though you have a combustion or not. 

b)  Your other appliances, such as hearths or other heating appliances, release odors, 

heat  badly,  provoke  smoke  return  or  a  counterblow,  even  though  there  is 
combustion or not. 

c)  An opened window, even slightly, by a calm temperature (without wind) stops the 

situation above. 

d)  Your  home  was  built  with  isolated  dandruffs  and  with  well  adjusted  windows, 

and/or was built with a mechanism to evacuate the interior air. 

 
If,  with  these  indications,  there  is  not  enough  air  infiltration,  you  must  ensure  an  air 
supply. 

*In doubt, it is recommended to ensure an air supply. 

Summary of Contents for ATFM




























Reviews: