background image

maintenance instructions

Model SEC 180

page 16 of  16

JARVIS

PRODUCTS CORPORATION

33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457–4926

UNITED STATES OF AMERICA

TEL. 860–347–7271   FAX. 860–347–6978

6204012::.

8 MOTOR ASSEMBLY:

8.1 Reverse steps and procedures outlined in section

7.  See notes below.

8.1.1 Ensure correct motor rotation by attaching

the garter springs to their original brush
holder.

8.1.2 Jarvis tool 8039140 is available for instal-

lation of needle bearing (item 42) and thrust
washer (item 41) into motor cover.   See Fig-
ure G on page 10.

8.1.3 Use thread locking compound when instal-

ling helical pinion gear (item 51) on shaft.

8.1.4 Evenly tighten screws (item 40) into bear-

ing retaining washer (item 56) so that is rests
flat against the outer bearing race.

9 REAR HANDLE DISASSEMBLY:

9.1 Remove rear handle cover (item 90) and rear

handle (item 79) from motor as outlined in sec-
tion 7, steps 7.17–7.21.

9.2 Remove self tapping screws (item 80) from rear

handle (item 79).

9.3 Remove switch and lever assembly (items

82–86).

9.3.1 Remove dowel pin (item 83).

9.3.2 Remove pan head screw (item 85).

9.3.3 Remove switch activating lever (item 82)

and switches (item 86) from switch holder
(item 84).

9.4 Remove internal retaining ring (item 88), ring

washer (item 87) and diaphragm seal (item
101).

9.5 Press dowel pin (item 107) from handle and re-

move trigger lever (item 106) and spring (item
78).

9.6 Clean and inspect all parts for wear and replace

if necessary.

10 REAR HANDLE ASSEMBLY:

10.1 Reverse steps and procedures outlined in section

9.

Summary of Contents for SEC 180

















Reviews: