background image

operation instructions

Model VC

page 8 of 12

JARVIS

6222009::.

PRODUCTS CORPORATION

33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457--4926
UNITED STATES OF AMERICA E--MAIL. jarvis.products.corp@snet.net
TEL. 860--347--7271 FAX. 860--347--6978 WWW.jarvisproducts.com

®

OPERATION INSTRUCTIONS

IMPORTANT: DISCONNECT THE AIR LINE IN ACCOR-
DANCE WITH OSHA’S LOCKOUT/TAGOUT PROCEDURES
(29 CFR 1910.147) BEFORE SHARPENING BLADES. DIS-
CONNECT THE AIR LINE IN ACCORDANCE WITH OSHA’S
LOCKOUT/TAGOUT PROCEDURES (29 CFR 1910.147) BE-
FORE PERFORMING ANY REPAIR OR MAINTENANCE.

Refer to pages 4 and 5 for all referenced items.

1 Attach the 8 ft. vacuum hose (1323010) to connector

(item 5).

2 Attach the 8 ft. water tube (1323019) to connector

assembly (item 13).

3 Attach the air hose (1323011) to quick connect cou-

pling (item 31).

4 Attach trigger control hose (1323015) to tube con-

nector (item 10).

5

Each day,

before you begin operation, go through

the following checklist:

5.1 Make sure that the Model VC moves freely on

its balancer.

5.2 Make sure that you are wearing a steel mesh

safety glove on the hand that will not be operat-

ing the Model VC.

6 Making the cut:

6.1 Pull the trigger until it touches the round trigger

on the motor. This activates the vacuum at the

blade

. Refer to Figure 1

.

Trigger in

rest position

Round motor

trigger

Trigger in

activated

position

Figure 1

6.2 With the vacuum activated, insert the pilot pin

(item 1) into the anus of the bird.

The entire anus

ring should be enclosed by the blade, and the

skin of the bird should be sucked up around the

entire cutting edge of the blade. Refer to Figure

2.

Anus

Anus ring

Backbone

Oil gland

Tail

Rosebud

gland

Pilot pin

Blade

Figure 2

6.3 While vacuum is holding the skin upward, pull

the trigger back fully and allow the blade to ro-

tate. Move the blade gently forward into the bird

about 1/2 to 3/4 of the length of the blade.

Do

not apply pressure on the bird until the blade is

rotating. Refer to Figures 3 and 4.

Proper Method

Rosebud gland

is inside of the

blade.

Skin is pulled up by

vacuum against the

cutting edge of the blade.

Figure 3

Improper Method

Skin is depressed

before the blade is

activated.

Rosebud gland

is outside of the

blade.

Figure 4

Summary of Contents for VC













Reviews: