Jason International, Inc. •
501.771.4477
Page 14 of 18
Customer Service : 800.255.5766
Copyright © 2011 Jason International.
The Jason Signature Edition MicroSilk-AirMasseur digital
touchpad is used to access all the functions of the two (2)
control boxes used on the Jason Signature Edition MicroSilk-
AirMasseur bath.
NOTe:
It is not recommended to operate the MicroSilk system at
the same time as the AirMasseur system as this could diminish
the effects of the MicroSilk system.
OpERAting instRuctiOns
microsilk On/Off icon
To control the operation of the MicroSilk pump motor, press and
release for each setting: ON or OFF. A 20 minute decreasing
timer will be initiated when the pump motor starts. Press and
hold the Pump icon to cycle through each pump setting. The
Pump icon lights when the water is at operating level and the
LCD displays “System Ready”. The LCD will display “Pump On”,
or “Pump Off” when the key is pressed. It also toggles between
Temperature and Timer at 5 second intervals. “Low Water” is
displayed for 5 seconds if no water is detected. “Vacuum Error”
is displayed if the MicroSilk suction is blocked.
blower On/Off and modes icon
To control the operation of the blower, simply press and release
to change the setting to Constant, Wave, Pulse or Off. A 20
minute decreasing timer will be initiated when the blower motor
starts. Press and hold the Blower icon to cycle though blower
modes. The Blower icon should remain lit as long as the bath is
connected to a power supply. The LCD will display “Const Air”
and blower speed, “Wave Air” and blower speed, or “Pulse Air”
and blower speed, while the key is pressed. The time remain-
ing on the purge cycle is displayed after the bath has drained.
“Purge Stop” is displayed while the key is pressed during the
purge cycle. This action will terminate the purge cycle. The
mode settings will be remembered on the next startup.
blower speeds icon
Hold the key in Constant mode to go from High to Low then
release and hold again to go from Low to High. Hold the key in
Wave and Pulse mode to go from High to Medium and Medium
to High. The system remembers the last speed setting on the
next startup. The Blower Speeds icon will light up when the
blower is running. The LED displays the blower speed from
“10” (Low) or “55”(Med) to “99” (High) while the key is pressed.
You can reduce the auto purge idle time from 20 minutes to
10 minutes, by pressing and holding the key for more than
5-seconds during the purge idle period.
LED Light icon
Hold the key for less than two (2) seconds to turn the lights
Off or On. Hold the key for more than two (2) seconds to
change modes. The Light icon should remain lit as long as
the bath is connected to a power supply. This function has a
two-hour timer and remembers the last mode. The LCD dis-
plays “Light On” or “Light Off while the key is pressed for less
than two (2) seconds, “Light Cycle” is displayed if pressed for
more than two (2) seconds.
customized settings
The 12 character LCD display can be customized by pressing
the Blower and Blower Speeds icon simultaneously for five (5)
seconds, while the system is off. Note : The Blower Speeds icon
will not be illuminated during this process. Use the above figure
to locate the icons and LCD display. A menu will be displayed
to choose the following: Purge 24, (starts the blower every 24
hours for two (2) minutes at the time the purge was set), Product
Test Diagnostics, Temperature (F or C) and Language (English
or Spanish).
menu instructions
Use the top Diagnostic Function icon to scroll through the
different menu items. Use the bottom Diagnostic Function icon
to change an option. For example, press and release the top
icon to change from Product Test to the Temperature option.
Press and release the bottom icon to change the temperature
display from F (Fahrenheit) to C (Celsius).
product test Diagnostics
After selecting the Product Test option from the menu, the unit
will perform a series of tests to confirm correct installation of
components. The test will begin by displaying the configuration
number, followed by the software revision number. Next,
the auxiliary control box will be tested to ensure proper IR
communication. The display will then test the Temperature and
Low Water level sensor (ITW-209). Next, each of the six (6)
icon buttons will begin to light. Press the illuminated button to
proceed to the next icon. After the icon test, the blower will start
for two (2) seconds on the High setting. Lastly, the LED Light
unit will be tested. If you receive an error on any of the tests,
confirm proper installation of component to the correct control
box. (See the
CONTROl bOX CONNeCTIONS
section).
Remote control
The Signature Edition control system includes a waterproof
floating Universal Remote Control. It controls all bath functions
plus a TV, DVD, CD, etc. which can be heard through the Sound
Immersion Transducers (optional).
signAtuRE EDitiOn
micROsiLk
tm
-AiRmAssEuR tOuchpAD
m
microsilk On/Off
LED Light
blower On/Off, modes
blower speeds
