background image

Jason International, Inc.  ·  501.771.4477                              Page 11 of 12                                              Customer Service: 800.255.5766 

Copyright © 2021 Jason International, Inc. 

 

 

 

If you believe the unit to be within the warranty period, you must contact 

Jason Customer Service: 1-800-255-5766

 

with the bath’s Product and Serial numbers before work is started.  These numbers can be found on the label on the 
front page of this manual and also adhered to the underside of the bath above the equipment. 

 

ALL WARRANTY REPAIRS MUST BE AUTHORIZED BY JASON BEFORE WORK IS STARTED. 

 

FOR SERVICE, ALWAYS CONTACT YOUR DEALER OR AUTHORIZED SERVICE CENTER. 

 

WARNING: Always turn off power at the main electrical service panel when servicing the bath 
 

ALL SYSTEMS

 

SYMPTOMS 

POSSIBLE CAUSES 

RECOMMENDED ACTION 

System fails to operate. 

a) No power to the motor or control box. 

 

a) Reset circuit breakers and GFCI 

if tripped.  Check fuses and replace 

if bad. Check voltage at motor when 

control is on.  If no voltage, control 

is defective. 

b) Motor is not plugged into control box. 

b) Make sure plug is fully inserted 

into the control box outlet. 

c) Air switch/Plastic air tubing 

disconnected or broken 

c) Check and reconnect if 

necessary. 

Equipment does not manually 

shut off. 

a) Control defective 

a) Refer to installer/dealer. 

Equipment shuts off by itself or 

before set time elapses. 

a) Motor overheated and thermal 

protection device deactivated motor. 

(Possible low voltage) 

a) Make sure motor has sufficient 
ventilation, clear and obstructions 

and allow motor to cool down.  

Check service and wire size. 

 

b) GFCI tripped. 

b) Refer to Jason Customer Service 

Circuit breaker trips repeatedly 

a) Defective breaker 

a) Replace breaker 

b) Short circuit between the bath and 

the breaker box. 

b) Refer to installer/dealer. 

c) Other items are connected to the 

same circuit. 

c) Refer to installer/dealer. 

 

 
 
 
 
 
 
 
 
 

AIRMASSEUR

®  

[AM] BLOWER SYSTEM

 

SYMPTOMS 

POSSIBLE CAUSES 

RECOMMENDED ACTION 

Blower turns on when not in 

use. 

a) Purge cycle has started. 

a) No action is needed.  This is a 

normal feature to help keep the air 

channel dry and sanitary. 

TROUBLE SHOOTING GUIDE

 

Summary of Contents for Excel













Reviews: