JASON Hydrotherapy forma AC553 Owner'S Manual Download

Page: 13 / 18

Jason International, Inc. •

501.771.4477

Page 13 of 18

Customer Service : 800.255.5766

STANDARD AND PReMIeR eDITION

MICROSILK

-WhIRLPOOL TOUChPAD

T h e J a s o n S t a n d a r d a n d P r e m i e r E d i t i o n

MicroSilk-Whirlpool touchpad is used to access

all of the functions of the MicroSilk and pump controls.

NOTE: It is not recommended to operate the MicroSilk

system at the same time as the Whirlpool system as this

could diminish the effects of the MicroSilk system.

OPeRATINg INSTRUCTIONS
Whirlpool On/Off Icon

The Whirpool icon is used to activate the whirlpool pump and

the 20-minute timer.

Pressing the icon the first time starts the pump.

•

Pressing the icon again will shut the pump off.

•

MicroSilk On/Off Icon

The MicroSilk icon is used to activate the MicroSilk pump

and the 20-minute timer.

Pressing the icon the first time starts the pump.

•

Pressing the icon again will shut the pump off.

•

MICROSILK™-wHIRLPOOL

LeD Light

Whirlpool On/Off

MicroSilk On/Off

Option

LeD Light Icon

The LED Light icon is used to operate an LED light (if installed).

Press the icon for less than two (2) seconds to turn the

•

lights Off or On.

Hold the icon for more than two (2) seconds to change

•

modes.

This function has a two (2) hour timer and remembers the

last mode.

Option Icon

This key is reserved for future enhancements.

Summary of Contents for forma AC553



















Search results

Summary of Contents for forma AC553

Reviews:

Related manuals for forma AC553

Brands by name

Popular brands

JASON Hydrotherapy forma AC553, Owner'S Manual

Search results

Summary of Contents for forma AC553

Reviews:

Related manuals for forma AC553

Brands by name

Popular brands