Jason International, Inc. •
501.771.4477
Page 14 of 18
Customer Service : 800.255.5766
Copyright © 2011 Jason International.
T h e J a s o n S i g n a t u r e E d i t i o n M i c r o S i l k -
Whirlpool digital touchpad is used to access all the
functions of the two (2) control boxes used on the
Jason Signature Edition MicroSilk-Whirlpool bath.
NOTE: It is not recommended to operate the MicroSilk
system at the same time as the Whirlpool system as this
could diminish the effects of the MicroSilk system.
OPeRATINg INSTRUCTIONS
Whirlpool On/Off Icon
To control the operation of the whirlpool pump motor, press
and release for each setting: High, Medium, Low, or Off. (For
50Hz controls: ON or OFF) A 20 minute decreasing timer will
be initiated when the pump motor starts. Press and hold the
Pump icon to cycle through each pump setting. The Pump
icon lights when the water is at operating level and the LCD
displays “System Ready”. The LCD will display “Pump Off”,
“Pump High”, “Pump Medium”, or “Pump Low” when the key
is pressed. It also toggles between Temperature and Timer
at 5 second intervals. “Low Water” is displayed for 5 seconds
if no water is detected.
Jetted Neck Pillow Icon [Optional]
To control the operation of the jetted neck pillow, press and
release for each setting, you can set for a constant flow on
both jets, a pulsing flow on both jets, or a pulsing alternating
flow between jets. Press and hold the Pillow icon to cycle
though the various pillow settings. The Pillow icon will light
whenever the pump is running. The solenoids will open for
two (2) minutes to drain during the purge cycle countdown.
The LCD will display “Pillow On”, “Pillow Pulse1”, “Pillow
Pulse2”, or “Pillow Off” while the key is pressed.
MicroSilk On/Off
To control the operation of the MicroSilk pump motor, press
and release for each setting: ON or OFF. A 20 minute de-
creasing timer will be initiated when the pump motor starts.
Press and hold the Pump icon to cycle through each pump
setting. The Pump icon lights when the water is at operating
level and the LCD displays “System Ready”. The LCD will
display “Pump On”, or “Pump Off” when the key is pressed.
It also toggles between Temperature and Timer at 5 second
intervals. “Low Water” is displayed for 5 seconds if no water
is detected. “Vacuum Error” is displayed if the MicroSilk
suction is blocked.
LeD Light Icon
Hold the key for less than two (2) seconds to turn the lights
Off or On. Hold the key for more than two (2) seconds to
change modes. The Light icon should remain lit as long as
the bath is connected to a power supply. This function has
a two-hour timer and remembers the last mode. The LCD
displays “Light On” or “Light Off while the key is pressed
for less than two (2) seconds, “Light Cycle” is displayed if
pressed for more than two (2) seconds.
Customized Settings
The 12 character LCD display can be customized by pressing
the two Diagnostic Function icons simultaneously for five (5)
seconds, while the system is off.
Note :
Use the above figure
to locate the icons. A menu will be displayed to choose the
following: Product Test Diagnostics, Temperature (F or C)
and Language (English or Spanish).
Menu Instructions
Use the top Diagnostic Function icon to scroll through the
different menu items. Use the bottom Diagnostic Function
icon to change an option. For example, press and release
the top icon to change from Product Test to the Temperature
option. Press and release the bottom icon to change the
temperature display from F (Fahrenheit) to C (Celsius).
Product Test Diagnostics
After selecting the Product Test option from the menu,
the unit will perform a series of tests to confirm correct
installation of components. The test will begin by displaying
the configuration number, followed by the software revision
number. Next, the auxiliary control box will be tested to
ensure proper IR communication. The display will then test
the Temperature and Low Water level sensor (ITW-209).
Next, each of the six (6) icon buttons will begin to light. Press
the illuminated button to proceed to the next icon. After the
icon test, the pump will start for two (2) seconds on the High
setting. Lastly, the LED Light unit will be tested. If you receive
an error on any of the tests, confirm proper installation of
component to the correct control box. (See the
CONTROL
BOX CONNECTIONS
section).
Remote Control
The Signature Edition control system includes a waterproof
floating Universal Remote Control. It controls all bath functions
plus a TV, DVD, CD, etc. which can be heard through the
Sound Immersion Transducers (optional).
SIgNATURe eDITION
MICROSILK
TM
-WhIRLPOOL TOUChPAD
MicroSilk On/Off
Pillow On/Off
Whirlpool On/Off
LeD Light
