Jason International, Inc. •
501.771.4477
Page 10 of 15
Customer Service : 800.255.5766
GENERAL OPERATING INSTRUCTIONS
INTRODUCTION
This manual contains all of the information needed for the
proper installation and operation of your Jason AirMasseur
®
bath. The AirMasseur
®
bath has been designed to give
you years of relaxing trouble-free service, provided the
unit is maintained and operated in accordance with these
instructions.
Thoroughly clean and disinfect the unit as described in the
CleaNING
section of the
user MaINTeNaNCe INsTruCTIONs
on
page 13 before its first use and periodically thereafter.
All Jason air baths are pre-plumbed at the factory.
WARNING: Before operating refer to the instructions pertaining to the
risk of fire, electric shock, or injury to persons.
fILLING AND DRAINING
Close the drain and fill the bath with water to at least 10” below
the bath deck. The inlet temperature should not exceed 40°C
(104°F) as this could damage the acrylic surface.
When the bath is in use, turn the unit
Off
before draining the
water. The bath unit and its plumbing are designed to drain
after each use whether used as an air bath, soaking bath, or
just taking a shower.
bLOwER
The blower generates the warm air and pushes it through
the air jets. Blowers provided on Jason air baths are factory
tested when assembled and retested after installation on the
AirMasseur
®
bath.
STANDARD EDITION AUTOMATIC PURGE
Fifteen minutes after the control has shut off and the bath is
completely drained, the blower will start again for a 2-minute
purge cycle that dries the air channel. Note that the blower light
will flash during the 15-minute pause before the purge cycle
begins. Once the purge cycle begins, all indicators will light and
the keypad operation will be disabled for two (2) minutes.
SIGNATURE EDITION AUTOMATIC PURGE
Twenty (20) minutes after the control has shut off and the bath
is completely drained, the blower will start again for a 2-minute
purge cycle that dries the air channel. Note that the LCD
display will read “PURGE” and begin to countdown the 10 or
20 minute pause before the purge cycle begins. The readout
will display “PURGE ON” during the purge cycle.
Any time during the pause before the purge cycle begins,
pressing and holding the Blower Speeds icon will reduce the
pause from 20 minutes to 10 minutes. During the 2-minute
purge, pressing the “Blower On/Off” icon will stop the purge.
SIGNATURE EDITION DAILY PURGE
The Daily Purge can be activated through the customized
settings of the Signature Edition touchpad. When activated
the daily purge will start the blower for 2-minutes at the same
time everyday to dry out the air channel. See ‘Operating the
Signature Edition AirMasseur
®
Touchpad’ section on page 12
for details on activating this setting.
INITALIZATION Of SIGNATURE EDITION CONTROL
SYSTEM
The blower junction box must be connected to its dedicated
service prior to filling the bath with water. This will assure the
control box is properly initialized. (See Figure 12 on page 9.)
SIGNATURE EDITION UNIVERSAL REMOTE
CONTROL
In addition to the main control console installed on the bath
deck, a floating, waterproof Universal Remote Control is
provided with all Signature Edition AirMasseur
®
baths. This
remote control is capable of operating the same functions as
the bath’s main control console, plus the bather may remotely
operate a TV, DVD, CD, etc. Refer to the Instruction Manual
provided with the remote control for detailed instructions.
NOTe:
If the unit fails to operate, check the breaker panel to
insure that the circuit breaker is on. Check the GFCI by testing
and resetting it. If the unit still fails to operate, refer to the
Trouble Shooting Guide section on page 14 of this manual.
If the unit still fails to operate and is out of warranty, contact
an authorized service technician for repair. If the unit is in
warranty, contact JASON Technical Services at 800-255-5766.
DO NOT ATTEMPT TO RESOLVE THE PROBLEM.
