background image

Jason International, Inc.  •  

 

501.771.4477  

 

 

 

Page 8 of 15

 

 

 

 

Customer Service :  800.255.5766 

fEATURES Of ThE DESIGNER AIRMASSEUR

®

 

bATh

bLOwER fEATURES

The Jason Standard Edition AirMasseur

®

 system provides 

a variable speed, controlled heated air blower with three (3) 

massage modes: continuous, wave, and pulse.

STANDARD EDITION AIRMASSEUR

®

TOUChPAD fEATURES

One main control touchpad mounted on the bath deck 

contains several icons used by the bather to control the 

blower and optional light. A built in timer shuts the blower 

off 20 minutes after being activated. A purge cycle will 

automatically start the blower again for 2 minutes, 15 

minutes after the bath has been shut off. This should be 

done in order to dry out the air channels.

bLOwER fEATURES

The Jason Signature Edition AirMasseur

®

 

air bath system 

includes a variable-speed, 1-HP air blower with heater; 

three (3) massage modes: continuous, wave, or pulse; and 

temperature sensors. A built in timer shuts the blower off 20 

minutes after being activated.
Also included is the Automatic Ozone Sanitation system to 

guard your bath from bacteria, viruses, etc. while leaving the 

plumbing lines clean and fresh.  The ozone system works 

automatically in conjunction with the blower motor.

TOUChPAD fEATURES

A  main  control  touchpad  mounted  on  the  bath  deck 

features an LCD readout which alternately indicates the 

water temperature (+/- 5°F) and air bath time remaining. 

The touchpad operates all functions of the blower as well 

as the LED Mood light. A built in timer shuts the blower 

off 20 minutes after being activated. A purge cycle will 

automatically start the blower again for two (2) minutes, 

10 to 20 minutes after the blower has been shut off. This 

should be done in order to dry out the air channels. A daily 

purge can also be set to turn the blower on at the same time 

everyday. (See the 

Customized Settings 

section on page 12).

SIGNATURE EDITION AIRMASSEUR

®

REMOTE CONTROL fEATURES

In addition to the main control touchpad installed on the 

bath deck, a floating, waterproof Universal Remote Control 

is provided with all Signature Edition AirMasseur

®

 baths. 

This remote control provides the same control functions 

as the bath’s main control console, plus the bather may 

remotely operate a TV, DVD, VCR, CD, etc. Refer to the 

Instruction Manual provided with the remote control for 

detailed instructions. 

Summary of Contents for Forma AirMasseur AC635P
















Reviews: