Jason International, Inc. •
501.771.4477
Page 2 of 15
Customer Service : 800.255.5766
Copyright © 2010 Jason International.
INSTALLATION
Remove the product from its packaging.
read the entire
instructions prior to installing this product.
see user MaInTenanCe InsTruCTIOns section of this owner’s
manual for humidity and mold prevention suggestions prior to
Installation.
1.
remove the packing board from the skirt
by placing the bath
and skirt assembly upside down and remove the four
press-in fasteners.
see figure1.
CauTIOn: Place bath deck on a surface that will not scratch the
acrylic surface of the bath.
2.
Disassemble the bath from its skirt
by removing the four nuts
and washers located at the bottom of the bath with a 1/2”
open ended wrench. Lift the skirt out of the bath. Place
the skirt and the bath in an upright position next to each
other.
See
figure 1.
3.
set aside the template, tubing with 2 clamps,
and locating stud
kit,
these will be used later.
4.
Blower Carton.
Remove the blower with stand, check valve,
and remote control (when supplied) from the separate
blower carton.
5.
Key Pad and sani Design Cleaning system Kit
. Set aside to
be installed later.
6.
Cardboard bath-well protector.
Each bath is provided with a
cardboard bath-well protector that should be kept in the
unit throughout the bathroom construction process.
nOTe:
Overflow drains, fill spouts, and valves must
be installed according to the instructions herein.
7.
Installation template.
An installation template is provided to
locate the floor drain position, sump area position, remote
blower-tubing floor cutout position, water inlet stub-out
position, and skirt center lines. Tape the template to the
sub-floor in the desired location.
8.
Mark on the sub-floor
the sump area position, the water
inlet stub-out position, and the remote blower-tubing floor
cut out position. One remote blower tubing, floor cutout
position and three (3) water inlet stub-out positions have
been indicated on the template. Choose the water inlet
stub-out position that is preferable for your installation.
9.
remove the template and cut out the floor.
CauTIOn:
The floor drain location must be installed according
to the template. This location is critical to the proper installation
of this product.
nOTe:
You must keep the template, it will be needed
during the next step of the installation process. See
figure 2
.
nOTe:
The skirt is designed to accommodate both an
end drain (Re630PS) and a center drain (RC630PS)
model. Refer to
figure 2
to determine which cut-outs
are designed for use with your particular model.
10
after the finished floor is installed,
position the installation
template on the finished floor. Place the template to line
up with the existing floor drain location and orient the
template to the desired position.
nOTe:
The sump area location cutout, remote blower
tubing floor location cutout, and water inlet stub-out
location must line up with the template.
nOTe:
The keypad and Sani-Design
tm
cleaning system
have not been installed. See the forma
TM
Collection
field Installation Instructions
for the AirMasseur
®
keypad
and Sani-Design
TM
cleaning system.
11.
Tape the template to the finished floor
using care to align
both center lines and assure that the template is laying
flat on the floor.
12.
Transfer the center lines of the template to the finished floor.
figure 1
INSTALLATION INSTRUCTIONS
TABLE 1 - SPECIFICATIONS
Model
Overall
Dimension
l x w x h (in.)
l x w x h (cm)
Operating
Capacity
gal
liters
Blower
hP
Min. size
access
w x h (in.)
w x h (cm)
floor
loading
lbs/ft
2
Kg/M
2
RE630PS
72 x 36 x 22
53
1
36 x 17
54.6 lbs
183 x 91 x 56
200
91 x 43
267 kg
RC630PS
72 x 36 x 22
50
1
36 x 17
53 lbs
183 x 91 x 56
189
91 x 43
259 kg
RC553PS
36 x 66 x 22
45
1
36 x 17
53.8 lbs
91 x 168 x 56
170
91 x 43
249
Remote Control
(When Supplied)
Control Box
(Signature Edition)
Blower with Stand
and Check Valve
Bath-Well Protector
Template
Tubing with
Clamps
Packing Board
Skirt
Bath
Keypad
Locating
Studs Kit
Sani Design
Cleaning
System Kit
5/16" Nut and
Washer (x4)
Press-in
Fasteners (x4)
Stabilizing Nut
and Washer (x4)
