AT-464
[RE5F22A]
TROUBLE DIAGNOSIS
Revision: November 2006
2006 Altima
2.
Touch “SELF-DIAG RESULTS”.
Display shows malfunction experienced since the last erasing
operation.
NOTE:
●
The details for “TIME” are as follow:
–
“CRNT”: Error currently detected with TCM.
–
“PAST”: Error detected in the past and memorized with
TCM.
●
Touch “F.F.DATA” on “SELF-DIAG RESULTS” screen to
display freeze frame data. Freeze frame data shows driv-
ing condition when malfunction is detected.
For freeze frame data items, refer to
Display item list
X: Applicable
—: Not applicable
SCIA2741E
Items (CONSULT-II
screen terms)
Malfunction is detected when...
TCM self-diagnosis
OBD-II (DTC)
A/T CHECK
indicator
lamp
*3
“TRANSMIS-
SION” with
CONSULT-II
MIL indicator
lamp
*1
,
“ENGINE” with
CONSULT-II or
GST
CAN COMM CIR-
CUIT
●
When a malfunction is detected in CAN communications
X
U1000
*4
U1000
*4
VEH SPD SE/CIR-
MTR
●
ECM detects a malfunction in vehicle speed sensor signal,
after that TCM inputs the result by CAN communication.
X
P0500
P0500
TCM PROCESSOR
●
TCM processor is malfunctioning.
—
P0613
—
PNP SW/CIRC
●
PNP switch signals input with impossible pattern
X
P0705
P0705
ATF TEMP SEN/
CIRC
●
Normal voltage is not applied to ATF temperature sensor
due to open, short, and so on.
●
During running, the ATF temperature sensor signal voltage
is excessively high or low.
X
P0710
P0710
FLUID TEMP SEN
●
ATF temperature signal does not change.
—
P0711
P0711
*2
TURBINE SENSOR
●
Signal from turbine revolution sensor does not input due to
open, short, and so on.
●
Unexpected signal input during running.
X
P0717
P0717
VHCL SPEED
SEN-A/T
●
Signal from revolution sensor does not input due to open,
short, and so on.
●
Unexpected signal input during running.
X
P0722
P0722
ENG SPD INP
PERFOR
●
Malfunction is detected in engine speed signal, actual
engine torque signal or torque reduction signal that is out-
put from ECM through CAN communication.
X
P0726
P0726
A/T 1ST GR
FNCTN
●
A/T cannot be shifted to the 1st gear position even if elec-
trical circuit is good.
X
P0731
P0731
*2
A/T 2ND GR
FNCTN
●
A/T cannot be shifted to the 2nd gear position even if elec-
trical circuit is good.
X
P0732
P0732
*2
A/T 3RD GR
FNCTN
●
A/T cannot be shifted to the 3rd gear position even if elec-
trical circuit is good.
X
P0733
P0733
*2
A/T 4TH GR
FNCTN
●
A/T cannot be shifted to the 4th gear position even if elec-
trical circuit is good.
X
P0734
P0734
*2
A/T 5TH GR
FNCTN
●
A/T cannot be shifted to the 5th gear position even if elec-
trical circuit is good.
X
P0735
P0735
*2
A/T TCC S/V
FNCTN
●
A/T cannot perform lock-up even if electrical circuit is
good.
X
P0744 P0744*2