background image

DTC U1000 CAN COMMUNICATION LINE

AT-471

[RE5F22A]

D

E

F

G

H

I

J

K

L

M

A

B

AT

Revision: November 2006

2006 Altima

DTC U1000 CAN COMMUNICATION LINE

PFP:23710

Description

ECS009DB

CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent malfunction detection ability.
Many electronic control units are equipped onto a vehicle, and each control unit shares information and links
with other control units during operation (not independent). In CAN communication, control units are con-
nected with 2 communication lines (CAN H line, CAN L line) allowing a high rate of information transmission
with less wiring. Each control unit transmits/receives data but selectively reads required data only.

On Board Diagnosis Logic

ECS009DC

This is an OBD-II self-diagnostic item.

Diagnostic trouble code “CAN COMM CIRCUIT” with CONSULT-II or U1000 without CONSULT-II is
detected when TCM cannot communicate to other control units.

Possible Cause

ECS009DD

Harness or connectors
(CAN communication line is open or shorted.)

DTC Confirmation Procedure

ECS009DE

NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”
and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.

 WITH CONSULT-II

1.

Turn ignition switch “ON”. (Do not start engine.)

2.

Select “A/T” with “DATA MONITOR” mode in CONSULT-II.

3.

Start engine.

4.

Drive vehicle and maintain the following condition for at least 6
seconds.
SLCT LVR POSI: “D” position

5.

If DTC is detected, go to 

AT-473, "Diagnostic Procedure"

 .

 WITH GST

Follow the procedure “WITH CONSULT-II”.

BCIA0030E

Summary of Contents for RE4F04B





































































































































































































































































































































































































































































































































































































































































































































Reviews: