manualshive.com logo in svg

Jatco RE4F04B, Manual

The Jatco RE4F04B is a reliable and durable automatic transmission system commonly used in various vehicles. Ensure proper maintenance of your transmission system by downloading the free user manual from 88.208.23.73:8080 to ensure optimal performance and longevity. Keep your vehicle running smoothly with a comprehensive manual at your disposal.

Share
Download
background image

AT-552

[RE5F22A]

DTC P0762 SHIFT SOLENOID VALVE C STUCK ON

Revision: November 2006

2006 Altima

DTC P0762 SHIFT SOLENOID VALVE C STUCK ON

PFP:31940

Description

ECS009GN

●

This malfunction will not be detected while the A/T CHECK indicator lamp is indicating another self-diag-
nosis malfunction.

●

This is not caused by electrical malfunction (circuits open or shorted) but by mechanical malfunction such
as control valve sticking, improper solenoid valve operation, etc.

●

Shift solenoid valves are installed directly in control valve body. The shift solenoid valves operates of ON
and OFF by the control signal from TCM. Combinations of 5 shift solenoid valves, A, B, C, D and E, shifts
gear positions.

●

The shift solenoid valve C is a normally closed, ON-OFF type solenoid.

On Board Diagnosis Logic

ECS009GO

●

This is an OBD-II self-diagnostic item.

●

Diagnostic trouble code “SFT SOL C STUCK ON” with CONSULT-II or P0762 without CONSULT-II is
detected when condition of shift solenoid valve C is different from monitor value, and relation between
gear position and actual gear ratio is irregular. 

Possible Cause

ECS009GP

●

Shift solenoid valve C
(On stick.)

●

Hydraulic control circuit

DTC Confirmation Procedure

ECS009GQ

CAUTION:

●

Always drive vehicle at a safe speed.

●

Be careful not to rev engine into the red zone on the tachometer.

NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”
and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.

 WITH CONSULT-II

1.

Turn ignition switch “ON”. (Do not start engine.)

2.

Select “A/T” with “DATA MONITOR” mode in CONSULT-II.

3.

Start engine.

4.

Drive vehicle and allow the following conditions.
SLCT LVR POSI: “D” position
GEAR: 3rd 

Þ

 4th position

ACCELE ANGLE: More than 10 %

5.

If DTC is detected, go to 

AT-554, "Diagnostic Procedure"

 .

 WITH GST

Follow the procedure “With CONSULT-II”. 

Gear position

D

1

 , M

1

D

2

 , M

2

D

3

 , M

3

D

4

 , M

4

D

5

 , M

5

Reverse

Shift solenoid valve C

ON (Open)

ON (Open)

ON (Open)

OFF (Closed)

OFF (Closed)

ON (Open)

BCIA0030E

Summary of Contents for RE4F04B





































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RE4F04B

N-Com B901 Quick Manual preview
B901
Brand: N-Com Pages: 2
Sanken CU-55 Instruction Manual preview
CU-55
Brand: Sanken Pages: 2
Samson CM11B Specifications preview
CM11B
Brand: Samson Pages: 2
CARVIN UX16-MC Instruction Manual preview
UX16-MC
Brand: CARVIN Pages: 4
Salus SG888ZB System Manual preview
SG888ZB
Brand: Salus Pages: 76
Shure Microflex MX400D Series User Manual preview
Microflex MX400D Series
Brand: Shure Pages: 20
Entel EA19 Quick Start User Manual preview
EA19
Brand: Entel Pages: 4
AKG C 4500 B-BC User Instructions preview
C 4500 B-BC
Brand: AKG Pages: 20
Beyerdynamic MCE 10 Product Information preview
MCE 10
Brand: Beyerdynamic Pages: 12
ClearOne Beamforming Microphone Array 2 Quick Start Manual preview
Beamforming Microphone Array 2
Brand: ClearOne Pages: 12
Teufel MD16 Technical Description And Operating Instructions preview
MD16
Brand: Teufel Pages: 16
Daewoo RG-361 Service Manual preview
RG-361
Brand: Daewoo Pages: 31
Pyle PDMIKT200 User Manual preview
PDMIKT200
Brand: Pyle Pages: 6
Music & Lights PROLIGHTS BlackBoxF1G4 User Manual preview
PROLIGHTS BlackBoxF1G4
Brand: Music & Lights Pages: 60
JTS RU-8011D-H Instruction Manual preview
RU-8011D-H
Brand: JTS Pages: 40
7RYMS SR-AU01 User Manual preview
SR-AU01
Brand: 7RYMS Pages: 20
Bosch pb360c Operating And Safety Instructions Manual preview
pb360c
Brand: Bosch Pages: 40
Bosch Plena LBB 1970 Installation And Operating Manual preview
Plena LBB 1970
Brand: Bosch Pages: 21

Brands by name

Popular brands

Load more brands