Jatco RE4F04B Manual Download

Page: 556 / 708

AT-556

[RE5F22A]

DTC P0762 SHIFT SOLENOID VALVE C STUCK ON

Revision: November 2006

2006 Altima

CHECK HARNESS BETWEEN TERMINAL CORD ASSEMBLY AND SHIFT SOLENOID VALVE C

Check the following.

●

Open or short-circuit in the harness between terminal cord assembly and shift solenoid valve C.

OK or NG

>> GO TO 7.

>> Repair or replace transmission wire. Refer to

AT-629, "Terminal Cord Assembly"

CHECK TCM

Check TCM input/output signal. Refer to

AT-459, "TCM Input/Output Signal Reference Values"

If NG, recheck TCM pin terminals for damage or loose connection with harness connector.

OK or NG

OK >> GO

>> Repair or replace damaged parts.

CHECK DTC

Perform “DTC Confirmation Procedure”. Refer to

AT-552, "DTC Confirmation Procedure"

OK or NG

>> INSPECTION END

>> Replace the control valve assembly. Refer to

AT-629, "Control Valve Assembly"

Component Inspection

ECS009GT

SHIFT SOLENOID VALVE C

Remove side cover. Refer to

AT-629, "Side cover"

Disconnect shift solenoid valve C harness connector.

Check resistance between terminal 1 and ground.

If NG, replace the control valve assembly. Refer to

AT-629,

"Control Valve Assembly"

Connector

Terminal

Condition

Resistance (Approx.)

F102

1 - Ground

Temperature: 20

C (68

11 - 16

Ω

SCIA4338E

Summary of Contents for RE4F04B





































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for RE4F04B

Reviews:

Related manuals for RE4F04B

Brands by name

Popular brands

Jatco RE4F04B, Manual

Search results

Summary of Contents for RE4F04B

Reviews:

Related manuals for RE4F04B

Brands by name

Popular brands