background image

8                                                                                                                                                                                                                                          

www.javad.com

The Serial RS-422 Straight Through cable should be wired according to 

the wiring table below.

Table: 4. 

Serial RS-422 Straight Through cable wiring table

DE-9 Female, side 1

Cable Wiring

DE-9 Female, side 2

Signal Name Pin

Wire Number

Pin

Signal Name

GND

5

Pair 1: Wire 1

5

GND

2

2

3

3

TXD+

7

Pair 2: Wire 1

8

RXD+

TXD-

3

Pair 2: Wire 2

2

RXD-

6

6

7

7

RXD+

8

Pair 3: Wire 1

7

TXD+

RXD-

2

Pair 3: Wire 2

2

TXD-

shell

Drain Wire

shell

USB connection

Evaluation Kit USB port may be used to connect OEM receiver with PC 

USB port. 
A standard USB 2.0 High Speed cable with USB type A Male connector 

on one side and USB type B Male connector on other side (not included 

in the Kit) may be used to connect OEM receiver with PC through J116 

USB type B Female connector on Evaluation Kit board. 
A standard USB 2.0 High Speed cable with USB type A Male connector 

on one side and USB type Mini-B Male connector on other side (not in-

cluded in the Kit) may be used to connect OEM receiver with PC through 

J115 USB type Mini-AB Female connector on Evaluation Kit board. 
For best results, we recommend to use as short as possible (from 0.5 

to 3 meters) USB high quality cables with marking similar to this: “USB 

SHIELDED 28AWG/1P + 24AWG/2C HIGH-SPEED USB 2.0”. USB connec-

tion cannot be used to connect two OEM receivers together directly for 

data exchange. This is because OEM receiver has “device” type of USB 

port, that may be connected only to “host” type of USB port, usually 

present on PC or on USB hubs.

Warning: 

Because both J116 USB type B and J115 USB type Mini-AB Female connec-

tors are physically connected to one and the same USB port, only one USB cable at a 

time may be used. Do not connect to Evaluation Kit two USB cables simultaneously.

Ethernet connection

The J119 “ETHERNET” port may be used to:
- connect OEM receiver with Local Area Network (LAN);
- connect OEM receiver with PC directly;
- connect two OEM receivers together directly.
For Ethernet connection we recommend to use short (from 1 to 10 me-

ters) high quality UTP 5 or 5e category cable with two RJ45 Male con-

nectors on both ends.
RJ45 Male connector external view and pinout shown below:

Figure 5. 

RJ45 Male connector

For direct connection between two OEM receivers or between one OEM 

receiver and PC, the Ethernet Crossover cable usually used. Crossover 

cable should be wired according to the wiring table below 

Table: 5. 

Ethernet Crossover cable wiring table.

RJ45 Male, side 1

Cable Wiring

RJ45 Male, side 2

Signal Name

Pin Pair Number: Wire Colour Pin

Signal Name

TX+ (BI_DA+)

1

Pair 2: White/Orange

3

RX+ (BI_DB+)

TX- (BI_DA-)

2

Pair 2: Orange

6

RX- (BI_DB-)

RX+ (BI_DB+)

3

Pair 3: White/Green

1

TX+ (BI_DA+)

- (BI_DC+)

4

Pair 1: Blue

7

- (BI_DD+)

- (BI_DC-)

5

Pair 1: White/Blue

8

- (BI_DD-)

RX- (BI_DB-)

6

Pair 3: Green

2

TX- (BI_DA-)

- (BI_DD+)

7

Pair 4: White/Brown

4

- (BI_DC+)

- (BI_DD-)

8

Pair 4: Brown

5

- (BI_DC-)

When two OEM receivers connected directly through Ethernet cable, 

one of them should be configured as Base (Server), while another re-

Summary of Contents for TR-G2 Series













Reviews: