ENGLISH
OPERATION
MANUAL
JB SYSTEMS®
1/30 TEXERCET
Thank you for buying this JB Systems product. To take full advantage of all possibilities and for your own
safety, please read these operating instructions very carefully before you start using this unit.
FEATURES
This unit is radio-interference suppressed. This product meets the requirements of the current European
and national guidelines. Conformity has been established and the relevant statements and documents
have been deposited by the manufacturer.
•
This device has been designed to produce decorative effect lighting and is used in light show systems.
•
Sound activated, multicolored gobo flower
•
18 gobos, including 6 multicolor gobos
•
Excellent optics for enhanced brightness
•
2 switches control gobo and reflector dish for
•
continuous or sound activated rotation
•
Sound activated by built-in microphone
•
Tomahawk:
equipped with an extra 90° sweeping scan mirror
•
Patriot:
equipped with an extra special quad angled 90° sweeping scan mirror
BEFORE USE
•
Before you start using this unit, please check if there’s no transportation damage. Should there be any,
do not use the device and consult your dealer first.
•
Important:
This device left our factory in perfect condition and well packaged. It is absolutely necessary
for the user to strictly follow the safety instructions and warnings in this user manual. Any damage
caused by mishandling are not subject to warranty. The dealer will not accept responsibility for any
resulting defects or problems caused by disregarding this user manual.
•
Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user
manual.
Check the contents:
Check that the carton contains the following items:
•
Operating instructions
•
Light effect
•
Hanging bracket
•
3 Knobs to fasten the hanging bracket
•
Lamp
ENGLISH
OPERATION
MANUAL
JB SYSTEMS®
2/30 TEXERCET
SAFETY INSTRUCTIONS:
•
To protect the environment, please try to recycle the packing material as much as possible.
•
A new light effect sometimes causes some unwanted smoke and/or smell. This is normal and
disappears after some minutes.
•
To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
•
To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures
when bringing it into a warm room after transport. Condense sometimes prevents the unit from working
at full performance or may even cause damages.
•
This unit is for indoor use only.
•
Don’t place metal objects or spill liquid inside the unit. Electric shock or malfunction may result. If a
foreign object enters the unit, immediately disconnect the mains power.
•
Locate the fixture in a well ventilated spot, away from any flammable materials and/or liquids. The
fixture must be fixed at least 50cm from surrounding walls.
•
Don’t cover any ventilation openings as this may result in overheating.
•
Prevent use in dusty environments and clean the unit regularly.
•
Keep the unit away from children.
•
Inexperienced persons should not operate this device.
•
Maximum save ambient temperature is 45°C. Don’t use this unit at higher ambient temperatures.
•
The units’ surface temperature may reach up to 85°C. Don’t touch the housing with bare hands during
its operation.
•
Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
•
Allow the device about 10 minutes to cool down before replacing the bulb or start servicing.
•
Always unplug the unit when it is not used for a longer time or before replacing the bulb or start
servicing.
•
The electrical installation should be carried out by qualified personal only, according to the regulations
for electrical and mechanical safety in your country.
•
Check that the available voltage is not higher than the one stated on the rear panel of the unit.
•
The power cord should always be in perfect condition: switch the unit immediately off when the power
cord is squashed or damaged.
•
Never let the power-cord come into contact with other cables!
•
This fixture must be earthed to in order comply with safety regulations.
•
Don’t connect the unit to any dimmer pack.
•
Always use an appropriate and certified safety cable when installing the unit.
•
In order to prevent electric shock, do not open the cover. Apart from the lamp and mains fuse there are
no user serviceable parts inside.
•
Never
repair a fuse or bypass the fuse holder.
Always
replace a damaged fuse with a fuse of the same
type and electrical specifications!
•
In the event of serious operating problems, stop using the fixture and contact your dealer immediately.
•
The housing and the lenses must be replaced if they are visibly damaged.
•
Please use the original packing when the device is to be transported.
•
Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
Important:
Never look directly into the light source! Don’t use the effect in the presence of persons
suffering from epilepsy.
