jbc AM 6800, Reference Manual

ENGLISH

2

SPECIFICATIONS

The

AM 6800

 is a rework station for through-hole

and SMT boards.

-

AM 6800

 230V

Ref. 6800200

-

AM 6800

 120V

Ref. 6800100

It contains 4 modules which cover the main rework
tasks:

-

Hot air

 for desoldering any size of SMD

components.
The station uses the exclusive JBC system,
based on protectors-extractors and hot-air
flow, which makes desoldering clean and quick,
concentrating the heat on the IC, and protecting
the rest of the circuit at the same time.
A medium-sized SMD can be desoldered in
less than 20 seconds.

-

Desoldering

 SMTs and cleaning of through-

hole components and pads by using the

DR 5650 

desoldering iron, which contains a

self-contained vacuum pump.

-

Pick & Place MP 2260

 pencil by suction to aid

components positioning.

-

Soldering

 of all types of components, with the

swift response, power and temperature
recovery of the JBC series.

Any of the JBC tools for soldering-desoldering

Any of the JBC tools for soldering-desoldering

Any of the JBC tools for soldering-desoldering

Any of the JBC tools for soldering-desoldering

Any of the JBC tools for soldering-desoldering
can be connected to the two modules:

can be connected to the two modules:

can be connected to the two modules:

can be connected to the two modules:

can be connected to the two modules:  the
soldering handpieces, the 

DR 5650 

desoldering

iron, the 

AP 1300 

solder feed iron and the tweezers.

The standardization of connections allows you to
adapt your configuration in the best way to your
job's needs. Do notice that you can connect only
one desoldering iron.

The station’s components

- Control unit with 

1000 W

 heater

-

2245

handpiece

Ref. 2245000

with the 

2245-003

cartridge

Ref. 2245003

-

DR 5650 

desoldering iron

Ref. 5650000

with the 

5600-003

tip

Ref. 5600003

-

MP 2260 

Pick & Place

Ref. 2260000

Accessories for the heater:

-

JT 8700 

heater stand

Ref. 0828700

- Extractor stand

Ref. 0932845

- Set of 5 protectors.
- Set of 5 extractors.
- 2 tripods for the protectors.
- Set of 4 suction cups

Ref. 0930110

- 3 nozzles:

ø 4

Ref. 0932015

ø 6

Ref. 0932012

ø 8

Ref. 0932020

In order to make the nozzles removal easier, the
stand  has a special bushing.

- Suction tube with connectors

Ref. 0932330

- Pedal with cable and connector Ref. 0964551

Accessories for the 

2245

 handpiece:

-

AD 8245 

soldering iron stand

Ref. 0788245

Accessories for the desoldering iron:

-

DR 8500

 desoldering iron stand Ref. 0788500

- External desoldering air filter

Ref. 0821830

- Spare filters

Ref. 0781046

- Set of accessories

Ref. 0780593

Accessories for the Pick & Place:

- Set of suction cups Pick & Place Ref. 0940163
- Set of straight needles

Ref. 0901546

- Set of bent needles

Ref. 0861660

- Instructions manual

Ref. 0002791

The

A M   6 8 0 0

  s t a t i o n   h a s   t h e   f o l l o w i n g

complementary products:

-

2210

handpiece

Ref. 2210000

-

PA 1200 

micro hot tweezers

Ref. 1200000

-

PA 4200 

hot tweezers

Ref. 4200000

-

AP 1300

 solder feed iron

Ref. 1300000

Control unit technical specifications

- Maximum power soldering iron 50W
- Maximum power desoldering iron 75W
- Power heating unit 1000W
- Temperature selection of the soldering part:

from 90 to 450°C or 190 to 840°F (±5%)

- Temperature selection hot air:

from 150 to 450°C or 300 to 850ºF (±5%)

- Air flow regulation: 6-45 l/min
- Self-contained vacuum pump for holding ICs
- Station's maximum power: 1150W
- ESD protected housing.

Typical surface resistance: 10

5

-10

11

Ohms/

square

- Complies with CE standards on electrical

safety,  electromagnetic compatibility and
antistatic protection.

- RoHS compliant.
- Equipotential connector and the tool tip are

connected to station mains ground supply for
ESD protection.

- Weight of complete unit: 19.8 kg

This product should not be thrown in the
garbage.