Tool
ON
MENU
28174
24 W 100%
18 W 100%
12 W 100%
6 W 100%
0 W 100%
10 seconds/div
V1.2
CHARGE
450 ºC
350 ºC
250 ºC
150 ºC
50 ºC
JBC
210
348ºC
5,7 W
80%
350ºC
Tool
ON
MENU
24 W 100%
18 W 100%
12 W 100%
6 W 100%
0 W 100%
10 seconds/div
V1.2
WORK
450 ºC
350 ºC
250 ºC
150 ºC
50 ºC
80%
JBC
210
350ºC
Tool
ON
MENU
24 W 100%
18 W 100%
12 W 100%
6 W 100%
0 W 100%
10 seconds/div
V1.2
CHARGE
450 ºC
350 ºC
250 ºC
150 ºC
50 ºC
JBC
210
348ºC
5,7 W
80%
350ºC
JBC#1
JBC#1
MENU
Tool1
2822
Tool ID
Hibernation delay
Temperature units
00:30
Maximum Temperature
400ºC
Sleep mode
Sleep temperature
150ºC
Working
Low battery
Power OFF
Charging
No cartridge
Tool Status
ºC
ºF
JBC
210
Lock Parameters
Locked
Unlocked
Return to Work
Tool1
Tool ID
28714
Hardware
Software
0028283
X886787
Update File
File
Hardware
Software
Select your Firmware
-
-
Update
MENU
JBC
210
Return to Work
JBC#1
Bi115
Bi210
User’s Manual
User’s Manual
Documents
MENU
JBC#1
JBC
210
Return to Work
2822
Work
Settings
Counters
Update
Documents
Light Theme
Dark Theme
Disconnect
JBC#1
Update
Tool
ON
MENU
JBC#1
24 W 100%
18 W 100%
12 W 100%
6 W 100%
0 W 100%
10 seconds/div
V1.2
WORK
450 ºC
350 ºC
250 ºC
150 ºC
50 ºC
80%
JBC
210
350ºC
Tool1
Tool1
Tool1
Tool1
Tool2
Tool3
Tool
ON
MENU
24 W
18 W
12 W
6 W
0 W
10 seconds/div
V1.2
CHARGE
450 ºC
350 ºC
250 ºC
150 ºC
50 ºC
JBC
210
80%
350ºC
JBC#1
348ºC
6 W
10
10
1
6
7
Status Lightband
Safety Cap
Safety Cap and Cap Holder
Cap Holders
Status Lightband Detail
8. Tool Selection
Screw
The status lightband indicates as follows the
tool status:
green
working/soldering
tool fully charged
green blinking
charging
alternating
red/green blinking
low battery,
less than 20%
red blinking
no cartridge
blue blink every few
seconds
the cap is on
and the tool is
disconnected
no color
power off
Thanks to the safety cap for B210 and B115
handles, tools can be safely transported even
with a cartridge inserted.
When the cap is placed onto the tool, the
cartridge stops heating
immediately,
data
transfer is cut off and the tool is disconnected
from the station. It turns off completely after 10
minutes of inactivity. This allows a greater saving
of the tool’s battery.
The stand has a holder for two safety caps on
the back. This component can be detached by
loosening and removing the screw between the
two holders (1).
While the tool is being used, the cap can be
stored on the cap holder.
Select the tool from the device list. If the tool is
not displayed on screen, make sure that the cap
is off and the tool has some battery. Try scanning
again by tapping
Scan
(6) on the display.
To add a second tool to the station once the fi rst
one is connected, go to the main menu (7) and
tap
Add device
. Select your second tool from
the device list.
9
40 mm
50 mm
60 mm
80 mm
100 mm
130 mm
130 mm
para manuales - color gris
200 mm
300 mm
