background image

www.jbctools.com

00

13

83

9-

04

14

TECHNICAL SPECIFICATIONS

-  Total unit weight: 2,6 Kg.
-   Size: 150 x 175 x 145 mm 
-  Temperature selection from 90°C (190°F) to 450°C (840°F) (±5%).
-  Output Peak Power CD-SC: 40W.
-  Safety transformer, mains separator and double isolation.

CD-2C

 230V 50/60Hz. Input fuse: 1A. Output: 23,5V.

CD-1C

 120V 50/60Hz. Input fuse: 2A. Output: 23,5V.

CD-9C

 100V 50/60Hz. Input fuse: 2A. Output: 23,5V.

-  Input Fuse 1A (230V), 2A (120V and 100V)
-  Tip to ground resistance <2 ohms
-  Tip to ground voltage <2mV RMS
-  Ambient operating temp: 10-40 ºC / 50-104 ºF
-  USB interface station-PC
-  Complies with CE standards
-  ESD protected housing “skin effect”

Warranty

JBC’s 2 year warranty covers this equipment 
against all manufacturing defects, including the 
replacement of defective parts and labour.
Warranty does not cover product wear due to use 
or mis-use. 
In order for the warranty to be valid, equipment 
must be returned, postage paid,  to the dealer 
where it was purchased.

This product should not be thrown in the garbage. 
In accordance with the European directive 2002/96/EC, electronic equipment at the end of their life 
must be collected and returned to an authorized recycling facility.

Summary of Contents for CD-SC













Reviews: