background image

  It is imperative to follow safety guidelines to prevent electric  
  shock, injury, fire or explosion. 

Safety

- Do not use the units for any purpose other than soldering or rework. Incorrect use may cause fire. 
 
- The power cord must be plugged into approved bases. Be sure that it is properly grounded  
  before use. When unplugging it, hold the plug, not the wire. 
 
-  Do not work on electrically live parts. 
 
- The tool should be placed in the stand when not in use in order to activate the sleep mode.  
  The soldering tip, the metal part of the tool and the stand may still be hot even when the station is  
  turned off. Handle with care.

- Do not leave the appliance unattended when it is on. 

- Do not cover the ventilation grills. Heat can cause inflamable products to ignite. 
 
- Avoid the contact of flux with skin or eyes to prevent irritation.

- Be careful with the fumes produced when soldering.

- Keep your workplace clean and tidy. Wear appropriate protective glasses and gloves when  
  working to avoid personal harm. 

- Utmost care must be taken with liquid tin waste which can cause burns. 

- This appliance can be used by children over the age of eight and also persons with reduced 
  physical, sensory or mental capabilities or lack of experience provided that they have been given  
  adequate supervision or instruction concerning use of the appliance and understand the hazards  
  involved. Children must not play with the appliance. 

- Maintenance must not be carried out by children unless supervised.

14

Summary of Contents for NAE-1C

















Reviews:

Related manuals for NAE-1C