jbc PHSE-K Instruction Manual Download | Manualshive

Page: 13 / 16

background image

Maintenance

Before carrying out maintenance or storage, always allow the equipment and the support to cool
down.

- Check periodically that the Pre Heater is clean.

- Use a damp cloth when cleaning. Alcohol can only be used to clean the metal parts.

- Only if it is absolutely necessary and if cleaning with isopropyl alcohol (IPA) is not enough, it is

recommended to use a scraper to remove dirt in the glass area.

- Replace any defective or damaged parts. Use original JBC spare parts only.

- Repairs should only be performed by a JBC authorized technical service.

13

www.jbctools.com

«
...
11
12
13
14
15
...
»

Summary of Contents for PHSE-K

















Reviews:

No comments

Related manuals for PHSE-K

Brand: RND lab Pages: 14

ATETOOL AT-689A

Brand: Atten Pages: 2

Brand: X-Tronic Pages: 20

Brand: jbc Pages: 4

Brand: jbc Pages: 12

Brand: TOOLCRAFT Pages: 60

Brand: jbc Pages: 16

Brand: jbc Pages: 24

Brand: Durite Pages: 2

Brand: Edsyn Pages: 4

Brand: jbc Pages: 12

Brand: OSEPP Pages: 11

Brand: Clarke Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands