JBL CINEMA VISION CVCEN50 Owner'S Manual Download

Page: 12 / 12

System

Frequency Response

22Hz – 20kHz (–6dB)

CVSAT50

Maximum Recommended Amplifier Power

150 Watts**

Power Handling

50W Continuous/300W Peak

Frequency Response

55Hz – 30kHz (–6dB)

Nominal Impedance

8 Ohms

Sensitivity

90dB @ 1 Watt/1 meter

Tweeter

One 3/4" (19mm) titanium-laminate dome,
video-shielded

Woofers

Dual 5" (130mm) transducers with PolyPlas

™

cones, neodymium magnets & HeatScape

™

motor structure, video-shielded

Dimensions (H x W x D)
(including wall-mount bracket and grille)

25-1/8" x 6-1/4" x 4-5/8" (638mm x 159mm x 117mm)

Weight

6.9 lb (3.1kg)

CVCEN50

Maximum Recommended Amplifier Power

150 Watts**

Power Handling

50W Continuous/300W Peak

Frequency Response

55Hz – 30kHz (–6dB)

Nominal Impedance

8 Ohms

Sensitivity

90dB @ 1 Watt/1 meter

Tweeter

One 3/4" (19mm) titanium-laminate dome,
video-shielded

Woofers

Dual 5" (130mm) transducers with PolyPlas

™

cones, neodymium magnets & HeatScape

™

motor structure, video-shielded

Dimensions (H x W x D)
(including wall-mount bracket and grille)

6-1/4" x 25-1/8" x 4-5/8" (159mm x 638mm x 117mm)

Weight

6.9 lb (3.1kg)

CVSUB50

Amplifier Power –

400 Watts RMS

Frequency Response

22Hz – Low-pass

crossover setting at signal source

Low-Frequency Driver

12" (300mm) Transducer with PolyPlas

™

cone & HeatScape

™

motor structure,

video-shielded

Input

LFE preamp level

Dimensions (H x W x D) (including feet)

18-3/4" x 12" x 18-1/4" (476mm x 305mm x 464mm)

Weight

49 lb (22.3kg)

SPECIFICATIONS

All features and specifications are subject to change without notice.

*Trademarks of Dolby Laboratories.

DTS is a registered trademark of Digital Theater Systems, Inc.

**The maximum recommended amplifier power rating will ensure proper system headroom to allow for occasional peaks.

We do not recommend sustained operation at these maximum power levels.

DESIGN GOAL:

Bring the thrill of live performance and movie sound

to the home environment by calling on JBL’s professional engineering leadership.

SATELLITE TYPE:

Titanium-laminate-dome tweeter,

sealed enclosure

SUBWOOFER TYPE:

Bass-reflex enclosure

PORT DESIGN:

FreeFlow

™

flared

PROFESSIONAL REFERENCE:

Cinema Loudspeaker Series

OWNER’S GUIDE

P R O D U C T

L I N E :

MODELS:

CVSAT50, CVCEN50, CVSUB50

JBL CINEMA VISION

™

JBL is a registered trademark of
Harman International Industries, Incorporated.

Part No. 406-000-01002

6/04

PRO SOUND
COMES HOME

™

JBL Consumer Products

250 Crossways Park Drive, Woodbury, NY 11797

8500 Balboa Boulevard, Northridge, CA 91329

516.255.4JBL (4525)

www.jbl.com

CV OM 6/15/04 4:06 PM Page 12

Summary of Contents for CINEMA VISION CVCEN50













Search results

Summary of Contents for CINEMA VISION CVCEN50

Reviews:

Related manuals for CINEMA VISION CVCEN50

Brands by name

Popular brands

JBL CINEMA VISION CVCEN50, Owner'S Manual

Search results

Summary of Contents for CINEMA VISION CVCEN50

Reviews:

Related manuals for CINEMA VISION CVCEN50

Brands by name

Popular brands