Service Bulletin
Service Bulletin JBL2003-01 Rev1 - June 2003
This is considered a Minor repair
To:
All JBL Service Centers
Model: DVD600II (Cinema ProPack
600II system)
Subject: Unit Says In Standby Mode
In the event you receive a DVD600II DVD player with the complaint: “The unit stays in standby mode
(amber indicator), and will not switch ON, either with the remote control or the front panel button”,
check the following components and follow the instructions below:
Synopsis:
In the Front panel PCB:
IC901 microprocessor - check solder connections to all 80 pins – resolder if necessary
C903, C904 0.1uF 50V SMD capacitors – check and replace.
In the Power supply PCB:
R6 120
Ω
1/8 watt resistor – check and replace if necessary.
1) Remove (8) screws holding the top cover on; remove the cover.
2) In the Power supply PCB, check and replace R6, 120
Ω
1/8 watt resistor, with JBL part# 299-120. You
may be able to cut the defective resistor off the PCB and re-solder the new part on without removing the
power supply PCB.
3) Remove the five plated screws holding the front panel to the chassis (one is on the bottom)
4) Unplug the single 5-pin Molex plug to CN906 (near the power switch) to allow the front panel to be
disengaged from the chassis; cut and remove any cables ties, but note their location.
5) Remove the front panel from the unit; there are four tabs/catches that must be freed as the panel is
removed; two are on the sides and two are on the bottom.
6) Once the rear of the front panel PCB is exposed, locate IC901 microprocessor - check solder
connections to all 80 pins and resolder if required.
7) Locate C903, C904; 0.1uF 50V SMD capacitors; check and replace with JBL part# 2026729091.
8) Replace any cable ties that were cut; reassemble and test unit.
Model
Serial number
(120v)
Serial number
(230v)
Status
Action
DVD600II
All Serial numbers
affected
All Serial numbers
affected
May need modification if
unit exhibits symptom
Check solder connections to IC901
Check and replace C903,C904 and R6
28
DVD600II
Summary of Contents for DVD600 II
