background image

ENGLISH

-14-

If there is no sound from any
of the speakers:

• Make sure the subwoofer is

plugged into an active AC wall
outlet.

• Make sure the Master Power

Switch, located on the rear of
the subwoofer, is in the
On/Standby position.

• Make sure there is a source –

for example, a DVD Player, CD
Player, VCR or television –
hooked up to one of the four
input jacks.

• Make sure that the program

material is playing.

• Recheck the hookup

connections, referring to the
Speaker Connections section.

If there is no sound from the
surround speakers or 
sound is very low:

• Check all connections

between processor/amplifier
and each of the speakers.

• Raise the surround volume

from the remote control (see
Operation section).

• Make sure the TV show or

movie you are watching is
recorded in surround, try the
Phantom or Simulated Sur-
round mode.

• Increase the surround- speak-

ers’ level, using the level-
adjustment instructions found
earlier in this manual. 

If there is no sound from the
center speaker:

• Make sure that the processor

is in the Surround or 
3-Stereo mode. If it is in
Phantom or Stereo mode, the
center speaker will not play.

• Increase the level of the cen-

ter channel, using the level-
adjustment instructions earli-
er in this manual.

• Check the connections

between the subwoofer and
the center speaker.

If you have low bass output:

• Experiment with placement of

the subwoofer. Remember,
place the subwoofer in a 
corner to get maximum bass
output from the system.

• Increase the subwoofer level,

using the level-adjustment
instructions found earlier in
this manual.

• Increase the level of bass,

using the remote control.

Troubleshooting

Specifications 

escXcite System

Power Output

Satellites:
25 Watts x 5 @ 1% THD
Subwoofer:
60 Watts x 1 @ 1% THD

Signal-to-Noise Ratio

80 dBA

Input Impedance

(analog inputs) 
20k Ohms

Input Sensitivity

(analog inputs) 
400mV

Auto Turn-On Sensitivity

(analog inputs) 
2mV

Frequency Response (–6 dB)

35Hz – 20kHz

Dimensions (H x W x D) 

Satellites (each):
111 x 80 x 92mm
Subwoofer:
315 x 300 x 310mm

Descriptions and specifications
subject to change without
notice.

Summary of Contents for escXcite















Reviews: