background image

12

sPecificaTiOns

gtO-804eZ

Number of Channels:

4

Power Output (CEA 2006A):

80W RMS x 4 channels at 4 ohms, 14.4V DC, <1.0% THD
100W RMS x 4 channels at 2 ohms, 14.4V DC, <1.0% THD
200W RMS x 2 channels bridged at 4 ohms, 14.4V DC, <1.0% THD

Max Power:

940W: 235W x 4 channels at 2 ohms (1kHz), 15.5V DC, 10% THD

Frequency Response:

20Hz – 23kHz (±0.5dB)

Crosstalk:

> 50dB @ 1kHz

Signal-to-Noise (@ 1W):

> 85dB

Maximum Current Draw:

60A

Fuse Replacement:

25A x 2

Dimensions (D x H x W):

11-15/16" x 2-9/16" x 9-11/16" (302mm x 66mm x 246mm)

Weight:

8.4 lb (3.8kg)

gtO-504eZ

Number of Channels:

4

Power Output (CEA 2006A):

50W RMS x 4 channels at 4 ohms, 14.4V DC, <1.0% THD
75W RMS x 4 channels at 2 ohms, 14.4V DC, <1.0% THD
150W RMS x 2 channels bridged at 4 ohms, 14.4V DC, <1.0% THD

Max Power:

640W: 160W x 4 at 2 ohms (1kHz), 15.5V DC 10% THD

Frequency Response:

20Hz – 23kHz (±0.5dB)

Crosstalk:

> 50dB @ 1kHz

Signal-to-Noise (@ 1W):

> 85dB

Maximum Current Draw:

40A

Fuse Replacement:

20A x 2

Dimensions (D x H x W):

8-3/8" x 2-9/16" x 9-11/16" (213mm x 66mm x 246mm)

Weight:

6.4 lb (2.9kg)

Summary of Contents for GTO-504EZ














Reviews: