33
FR
2 cm sous la surface de l’eau. Les fentes entre les différents modules ne doivent pas être
obstruées par des plantes ou des objets décoratifs.
2.
Installation SANS compte-bulles (8)
Couper le tuyau de CO
2
(11) avec des ciseaux à environ 30 cm de la partie supérieure
du réacteur et placer les bouts libres sur les tubulures du clapet anti-retour (9) en prenant
garde au sens du flux. Si l‘aquarium ne permet pas d’observer facilement le réacteur afin
de contrôler le nombre de bulles, installer le compte-bulles (8) comme indiqué au point 4.
Veiller alors à ce que le clapet anti-retour (9) soit correctement positionné entre le détendeur
ou le système de contrôle de pH et le compte-bulles.
3.
m
601,
m
602 : Installer le test permanent de CO
2
(12) dans l’aquarium selon le mode
d’emploi joint.
4.
Installation
AVEC
compte-bulles (8) :
Choisir un endroit qui permette une observation aisée et installer le compte-bulles (8) à
cet emplacement. Le compte-bulles peut être fixé, soit à l’aide de ventouses (par exemple
sur l’aquarium), soit à l’aide de vis (fournies) sur un mur ou un meuble. Découper le tuyau
de CO
2
de manière correspondante et fixer les extrémités libres sur les raccords à vis
du compte-bulles. Veiller à bien raccorder le tuyau d’arrivée de CO
2
sur le tube le plus
long du compte-bulles. ouvrir le compte-bulles en tournant d’un quart de tour (fermeture
à baïonnette), le remplir d’eau jusqu’au repère et le refermer. Le clapet anti-retour (9) doit
nécessairement être installé sur le tuyau d’arrivée du CO
2
avant le compte-bulles
, dans
le sens du flux du gaz, c’est-à-dire entre le détendeur ou le système de contrôle de pH et
le compte-bulles. Si ce n’était pas le cas, l’eau contenue dans le compte-bulles pourrait
pénétrer à l’intérieur de ces appareils et les endommager.
Pour les systèmes
u
403,
m
603,
m
1003 :
Choisir un emplacement adapté et permettant une observation aisée pour installer
l’ordinateur de contrôle du pH (7). Placer le tuyau de CO
2
sur les raccords à vis de
l’ordinateur selon le schéma. Vous trouverez d’autres informations détaillées dans le mode
d’emploi spécifique joint.
5.
Installer la bouteille à un endroit stable hors de portée des enfants (par exemple dans le
meuble de l’aquarium). Glisser la bouteille rechargeable
m
500 (1) dans le pied-support. La
bouteille rechargeable
m
2000 (2) et la bouteille à usage unique
u
500 (3) sont autoportantes.
Placer la bouteille à l’endroit choisi.
6.
Raccorder le détendeur (pour
u
402 et
m
602 avec l’électrovanne intégrée) sur la bouteille
de CO
2
:
Installations
u
401,
u
402,
u
403 : Enfiler rapidement en tournant le filetage intérieur
du détendeur (5, 6) sur le filetage extérieur de la bouteille à usage unique (3). Au bout
de quelques tours on entend un sifflement bref. Continuer à tourner jusqu’à sentir une
résistance. Donner encore à peu près un demi-tour, jusqu’à ce que le détendeur soit
fermement fixée. Le manomètre de gauche indique alors une pression de la bouteille de
60 bars environ et celui de droite la pression de service de 1,5 bars environ. Fermer la vis
d’ajustage en tournant dans le sens des aiguilles d’une montre, dans le cas où elle ne serait
pas encore fermée.
Systèmes
m
601,
m
602,
m
603,
m
1003 : Tourner l’écrou arrière du détendeur (4, 6) sur le
filetage extérieur de la bouteille rechargeable
m
500 (1) ou
m
2000 (2). Serrer l’écrou de
raccordement à l’aide de la clé jointe. Fermer la vis d’ajustage en tournant dans le sens des
aiguilles d’une montre, dans le cas où elle ne serait pas encore fermée.
Ne jamais utiliser
les bouteilles de CO
2
en position couchée ou la tête en bas. Ceci peut gravement
endommager le détendeur.
Summary of Contents for ProFlora m1003
