130
RU
3.
Для установки запасного баллона CO
2
выберите место со стабильным основанием
и вне досягаемости детей (напр., тумбу под аквариум). Вставьте многоразовый
запасный баллон
m
500 (1) в подставку. Многоразовый запасный баллон
m
2000 (2)
и одноразовый запасный баллон
u
500 (3) стоят сами по себе. Поместите запасный
баллон на предназначенное место.
4.
Присоедините арматуру устройства регулирования давления к запасному баллону:
для
u
501,
u
504
,
u
502:
быстро и плавно накрутите арматуру устройства регулирования давления (5, 6) с
обратной внутренней резьбой на внешнюю резьбу одноразового запасного баллона
(3). Через несколько оборотов послышится короткое шипение. Продолжайте
крутить быстро и плавно, пока не почувствуется сопротивление, после чего
сделайте еще пол-оборота, чтобы закрепить позицию арматуры.
Для
u
501,
u
502:
теперь левый манометр показывает давление внутри баллона, примерно 60 bar, а
правый манометр – рабочее давление, примерно 1,5 bar.
Закройте регулировочный винт по часовой стрелке, если он еще не был закрыт.
Для
m
501,
m
502,
m
503,
m
2003:
накрутите обратную соединительную гайку арматуры устройства регулирования
давления (4, 6) на внешнюю резьбу вентиля многоразового запасного баллона
m
500 (1) и (или)
m
2000 (2). Соединительная гайка выполнена в виде гайки с накаткой
для прикручивания БЕЗ использования инструментов! Затяните ее от руки, не
пользуясь инструментами. Закройте регулировочный винт по часовой стрелке,
если он еще не был закрыт.
Запрещается эксплуатировать запасные баллоны
в лежачем или перевернутом положении!! Этим можно вывести редуктор из
строя!!
5.
Прикрепите шланг CO
2
на место резьбового присоединения на арматуре
устройства регулирования давления (4, 5) или электромагнитном клапане (6).
6.
Для
u
501,
u
504:
медленно откройте регулировочный винт на арматуре устройства регулирования
давления и установите счетчик пузырьков на значение 10 – 15 пузырьков (примерно
15 – 20 пузырьков в реакторе). Сначала пузырьки проходят по реактору медленно и
частично собираются в большие пузыри.
Реактору необходимо приработаться в
течение примерно 48 часов!
Только по истечении этого времени на поверхности
реактора образуется биопленка, хорошо пропускающая пузырьки наверх. По
истечении времени приработки установите количество пузырьков, необходимое
Вашему аквариуму, как рассказано в гл. 12.3.
m
501:
откройте вентиль многоразового запасного баллона полностью. Теперь левый
манометр показывает давление внутри баллона, примерно 60 бар, а правый
манометр – рабочее давление, примерно 1,5 бар. Дальнейшие шаги выполняйте
по описанию для установки
u5
01.
u
502 und
m
502:
сначала вставьте блок питания электромагнитного клапана в розетку тока
постоянной нагрузки и соедините 12-вольтовый кабель блока питания с кабелем
электромагнитного клапана. Дальнейшие шаги для установки
u
502 выполняйте