background image

 

User Manual

42

 PHYSICAL 

Enclosure :

Polypropylene, aluminum baffle, plywood internal bracing, four integral recessed handholds  

IP Rating

7

 :

IP54   

Suspension :

Three-point, captive suspension plates, quick release pins, steel with anti-corrosion coating

Inter-enclosure Angle (deg) :

0.5, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12

Grille :

Powder coated 1.5 mm (16-gauge) hex perforated steel with acoustically transparent black cloth backing

Dimensions (H x W x D) :

305 mm x 716 mm x 519 mm

12.0 in x 28.2 in x 20.5 in 

Net Weight :

Shipping Weight :

26.7 kg (59 lbs) 

30.3 kg (67 lbs)  

 NETWORKING

 

Type :

TCP/IP    

Protocol :

Harman HControl   

Speed :

Dual 100 Mbps ports    

Connectors :

(2) Neutrik etherCON

®

  

 AC POWER

 

Voltage Range

Nominal :

Limits :

  

100-240 VAC, 50/60 Hz  

80-260 VAC, 50/60 Hz  

Connectors :

Dual (IN/OUT) Neutrik powerCON TRUE1 TOP

®

   

 CURRENT DRAW

120 V

208 V

240 V

Idle :

0.3 A     

0.2 A

0.2 A

Standby :

0.2 A    

0.1 A

0.1 A

 Continuous

4

 :

1.9 A   

1.1 A

1.0 A

Maximum Instantaneous Peak

5

 :

7.0 A    

6.4 A

6.2 A

Peak Inrush

6

 :

2.2 A     

3.6 A

4.3 A

 ORDERING INFORMATION

 

SKU :

JBL-P3234MX | SRX910LA for Global

JBL-P3247MXCN | SRX910LA for China

Included :

(1) SRX910LA | (1) Neutrik NAC3FX-W-TOP | (1) Neutrik NAC3MX-W-TOP   

Footnotes:

4: System test using IEC shaped pink noise with 9 dB crest factor. System at maximum output without clipping or limiting. Ambient temperature: 20° C. Duration: 5 sec.

5: Two-tone, all channels driven, IMD test at maximum power and a duration of 200 ms.

6: Measured RMS inrush current for a 50 ms window.

7: With use of SRX900 RC1 rain cover (JBL-P3239MX ) and front face at -10 degrees or greater down angle to allow the cabinet to drain water. Suspension components fully weather rated for indoor or covered outdoor 

conditions where humidity is nominally under 50% and not local to bodies of corrosive materials.

Summary of Contents for SRX900 Series




















































Reviews: