background image

 

 

Canada — Industry Canada (IC)

 

This device complies with RSS 210 of Industry Canada.                                            
Operation is subject to the following two conditions: (1) this device may not 
cause interference, and (2) this device must accept any interference, including 
interference that may case undesired operation on this device.                            
The Term “IC” before the equipment certification number only signifies that 
the Industry Canada technical specifications were met.

 

USA-Federal Communications Commission (FCC)

 

Page 3

 

This equipment has been tested and found to comply with the limits for a 
Class B digital device, pursuant to Part of FCC Rules. These limits are designed 
to provide reasonable protection against harmful interference in a residential 
installation.

 

JC LAB Support

 

If you require any additional help your devices or if you are having problems 
operating devices, you may need to contact JC LAB for additional technical 
assistance.

 

Before you call

 

Some problem you experience may be related to software, apps or the 
operating system so it is importance that you investigate other sources of 
assistance first.                                                                                                                  
Before contacting JC LAB, try the following:                                                                  
Review troubleshooting sections in the documentation supplied withyour 
software and/or peripheral devices.                                                                             
If problem occurs when you are running in your computer systems, consult the 
software document for troubleshooting suggestions and consider calling the 
system  company’s technical support department for assistance.                     
Consult the reseller or dealer from where you purchased your devices and 
software— they are your best resource for current information and support.

 

JC LAB technical support

 

If you are still unable to solve the problems and suspect that it is hardware 
related, visit JC LAB technical support website                                                               

http://www.jc-lab.jp

 

1.0 Copyright

 

Summary of Contents for Bimc-01NS













Reviews: