background image

 01 - Machine

 33 - Cleaning

 00 - General

01 - 23

9813/5500-1

01 - 23

00 - General

Introduction 

....................................................

 01-23

Preparation 

....................................................

 01-24

Introduction

WARNING

 When using cleaning agents, solvents

or  other  chemicals,  you  must  adhere  to

the  manufacturer's  instructions  and  safety

precautions.

CAUTION

  To  avoid  burning,  wear  personal

protective  equipment  when  handling  hot

components. To protect your eyes, wear goggles

when using a brush to clean components.

Notice: 

  Cleaning  metal  parts  with  incorrect

solvents  can  cause  corrosion.  Use  only

recommended cleaning agents and solvents.

Notice: 

 The efficiency of the rams will be affected

if they are not kept free of solidified dirt. Clean dirt

from around the rams regularly. When leaving or

parking the machine, close all rams if possible to

reduce the risk of weather corrosion.

Notice: 

 Never use water or steam to clean inside

the cab. The use of water or steam could damage

the on-board computer and render the machine

inoperable. Remove dirt using a brush or damp

cloth.

Clean the product with water and/or steam. Do not

let mud, debris etc. to collect on the product.

Before you do any service procedures that require

components to be removed:

The cleaning must be done either in the area

of components to be removed, or in the case

of major work, or work on the fuel system, the

whole engine and the surrounding product must

be cleaned.

When cleaning is complete, move the product

away  from  the  wash  area  or  alternatively,

remove the material washed from the product.

When  you  remove  components,  be  aware  of

exposure to dirt and debris. Cover any open ports

and remove the deposits before proceeding.

Detergents

Do  not  use  a  full  strength  detergent.  Always

dilute  the  detergents  as  per  the  manufacturer's

recommendations, or damage to the paint finish can

occur.

Always  obey  the  local  regulations  regarding  the

disposal of debris created from cleaning the product.

Pressure Washing and Steam Cleaning

CAUTION

  When  using  a  steam  cleaner,  wear

safety  glasses  or  a  face  shield  as  well  as

protective  clothing.  Steam  can  cause  personal

injury.

Summary of Contents for 2DXL










































Reviews: