background image

 P/N 960-000175R_Rev. A {EDP #233426}

 © 2014, JAPAN CASH MACHINE CO., LTD.

1 6

 DBV

®

 Series Banknote Validator (DBV-400) Integration Guide

Retrieving Banknotes

To retrieve Cash Box deposited Banknotes, perform 

the following steps:

1.  Press the Cash Box Release Button (See Figure 6 

a

) and slightly pull upward and then out in the 

direction indicated by the red arrow.

2.  Press the Cash Box Door Open/Close Button 

(See Figure 7 

a

) to open the Cash Box Door and 

retrieve the Banknotes.

Clearing a Banknote Jam

To retrieve a jammed Banknote located inside the 

Banknote Validator, proceed as follows:

1.  Press the Validation Guide Open/Close Latch 

(See Figure 8 

a

) upward and pull the Validation 

Guide out of the DBV-400 Unit as indicated by 

the red arrow 

A

.

2.  Remove the jammed Banknote (See Figure 9).

3.  When a jammed Banknote is not visible, open the 

Cash Box Door and remove any jammed 

Banknote found there (See Figure 10).

5 PREVENTIVE MAINTENANCE

Figure 6 

Retrieving Banknotes 1

a

Figure 7 

Retrieving Banknotes 2

a

Figure 8 

Clearing a Banknote Jam 1

a

A

Figure 9 

Clearing a Banknote Jam 2

Figure 10 

Clearing a Banknote Jam 3

Summary of Contents for DBV Series



















































Reviews:

Related manuals for DBV Series