background image

P/N 960-100925R_Rev. A {EDP #186705} 

© 2010, Japan CashMachine Co, Limited

8

Transaction Based Validator Integration Guide

   

Primary LED Indications

The following Table 14 Color LED indications 

occur during various TBV operating and error 

conditions.

Table 11 

TBV Centering Mechanism & Select 
Comm Interface Switches DS4

Switch No.

Switch ON

Switch OFF

1

Fixed Model

Centering Model

2

Barcode Coupon 

Single Read

*

*. When using the “Single Read” Barcode Coupon setting, its Checksum may have 

to be changed to improve reading accuracy. The “Double Read” setting however, 
has a higher reliability and read accuracy by the TBV Validation System.

Barcode Coupon 

Double Read

*

3

†. Match each setting to equal the setting of DIP Switch DS5 Switch #1.

4

Table 12 

TBV Photo-Coupler/RS232 Interface 

Selection Switch DS5

Switch No.

Switch ON

Switch OFF

1

*

*. Match each setting to DIP Switch DS4 Switches #3 & #4.

Photo-Coupler

RS232

Table 13 

TBV Option Memory Selection Switches 

DS6

Switch No.

Switch ON

Switch OFF

1

N/A

*

*. Not Applicable (N/A). Never Switched to ON.

OFF (Fixed)

2

N/A*

OFF (Fixed)

Table 14 

LED Error Pattern Indications

Mode

TBV LED 

Indication

TBV Condition

Normal 

Mode

Lit Blue

Stand-by (Waiting for a Banknote 

insertion)

Lit Yellow

Waiting for a Host Machine

Command

OFF

(Extinguished)

BUSY (Processing Validation) or an 

INHIBIT Command

Lit Green

Cash Box Near Full detection

Yellow Flashes Internal processing (Self download: 

Transport Section 

 BNF Section)

Yellow Flashes

*

*. Returns to Stand-by Mode after clearing the error condition (See “Standard 

Error Codes” on page 22 of this Guide to resolve the error type).

Banknote Jam or Setting malfunction

Red Flashes

†. Returns to Stand-by Mode from a RESET Command, or after clearing the error 

condition (See “Standard Error Codes” on page 22 of this Guide to resolve the 
error type).

Abnormal (ABN) Error

Download 

Mode

Green Flashes Waiting for a Download
Yellow Flashes Downloading

Lit Blue

Download completed

OFF

DS4

ON

Set Identical

I/F Selection

Switch #3

Switch #4

RS232

OFF

OFF

Photo-Coupler

ON

OFF

ccTalk

OFF

ON

ccTalk with Encryption

ON

ON

RS232

Photo-Coupler

DS5

ON

OFF

ON

OFF

DS6

Summary of Contents for TBV Series











































Reviews: