P/N 960-100925R_Rev. A {EDP #186705}
© 2010, Japan CashMachine Co, Limited
2 2
Transaction Based Validator Integration Guide
Standard Error and Reject Codes
The Bezel LED indicates various solid/flashing Color lighting conditions when any of the Standard Errors
listed in Table 21 occur. Identify the cause and solutions for these indications from each Table listing and
ensure that the relative assembles are properly connected and/or harnessed, and that all of the Unit’s
Sensors are clean.
S
TANDARD
E
RROR
C
ODES
Table 21 lists the various LED Flash Error Code causes & solutions.
Table 21
Standard LED Error Codes
On-line
Off-line
Error
Causes and Solutions
LED Color
(Flash
Sequence)
LED Color
(Flash
Sequence)
Yellow
(1)
Yellow
(1)
Banknote Jam (in
the Cash Box)
When transporting a Banknote to the Cash Box, the Sensors are not detecting a
Banknote present condition when the time interval taken is too long or the number
of the Banknotes stuck is greater than specified value for that function.
[Solution] Check that the following parts are properly assembled and/or Harness
connected. Clean or adjust the following parts and Sensors.
[Relative Parts] Feed Motor, Stack Sensor, Feed-out Sensor.
If the error is not resolved, change the above related part or parts.
Yellow
(2)
Yellow
(2)
Banknote Jam (in
the Transport
Section)
When transporting or returning a Banknote in the Transport Section, the Sensors
do not detect a Banknote present condition when the time interval taken is too long
or the number of the Banknotes stuck is greater than specified value for that
function.
[Solution] Check that the following parts are properly assembled and/or Harness
connected. Clean or adjust the following parts and Sensors.
[Relative Parts] Feed Motor, BNF Entrance Sensor, BNF Assignation Sensor,
Entrance Sensor, Centering Sensor, Line Sensor, Feed-out Sensor.
If the error is not resolved, change the above related part or parts.
Yellow
(3)
Yellow
(3)
Banknote Chain
While performing a BNF Banknote assignation, the Sensors do not detected a
Banknote present condition when the time interval taken is too long or the number
of the Banknotes stuck is greater than specified value for that function.
[Solution] Check that the following parts are properly assembled and/or Harness
connected. Clean or adjust the following parts and Sensors.
[Relative Parts] BNF Feed Roller, BNF Retard Roller, BNF Assignation Sensor,
Entrance Sensor, Feed-out Sensor.
If the error is not resolved, change the above related part or parts.
Yellow
(4)
Yellow
(4)
Cash Box Removal
The Cash Box has been removed.
[Solution] Check that the following parts are properly assembled and/or Harness
connected. Clean or adjust the following parts and Sensors.
[Relative Parts] Cash Box Sensor.
If the error is not resolved, change the above related part or parts.
Yellow
(5)
Yellow
(5)
Fraud Detection
Sensors detect Banknotes remaining in path or none exist during an abnormal
timing operation.
[Solution] Check that the following parts are properly assembled and/or Harness
connected. Clean or adjust the following parts and Sensors.
[Relative Parts] Line Sensor, Feed-out Sensor, Cash Box Feed-out Sensor, Side
Sensor.
If the error is not resolved, change the above related part or parts.
Yellow
(6)
Yellow
(6)
Cash Box Lock
Released
Sensors detect that the Cash Box Lock has been opened.
[Solution] Check that the following parts are properly assembled and/or Harness
connected. Clean or adjust the following parts and Sensors.
[Relative Parts] Cash Box Lock Sensor.
If the error is not resolved, change the above related part or parts.
Yellow
(7)
Yellow
(7)
Transport Section
Upper Cover Open
Sensors detect that the Upper Cover of the Transport Section has been opened.
[Solution] Check that the following parts are properly assembled and/or Harness
connected. Clean or adjust the following parts and Sensors.
[Relative Parts] Entrance Sensor, Centering Sensor.
If the error is not resolved, change the above related part or parts.
Red
(1)
Red
(1)
Cash Box Full
While stacking a Banknote, the Cash Box Full Sensors detect that the Cash Box is
full.
[Solution] Check that the following parts are properly assembled and/or Harness
connected. Clean or adjust the following parts and sensors.
[Relative Parts] Cash Box Full Sensor, Pusher Mechanism, Pusher Plate.
If the error is not resolved, change the above related part or parts.
Red
(2)
Red
(2)
Feed Motor
Lock-up Problem
While operating the Feed Motor, no pulse inputs exist greater than the rated value.
[Solution] Check that the following parts are properly assembled and/or Harness
connected. Clean or adjust the following parts and Sensors.
[Relative Parts] Feed Motor, Feed Encoder.
If the error is not resolved, change the above related part or parts.
