P/N 960-000180R_Rev. 1 {EDP #233427}
© 2016, JAPAN CASH MACHINE CO., LTD.
1 - 2
Section 1
DBV® Series DBV-400 Banknote Validator
General Information
Product Descriptions
Model Descriptions
Table 1-1 lists the product model number
descriptions.
Type Descriptions
Table 1-2 lists the product type number
descriptions.
Software Descriptions
Table 1-3 lists the product software number
descriptions.
Precautions
Symbols in Figure 1-2 are defined as follows:
1.
(Type 1)
Do not insert a torn, folded, or wet
Banknote; it may cause a jam inside the unit.
2.
(Type 2)
Do not expose the unit to water. The unit
contains several precision electronic devices that
can be damaged if water or any liquid is sprayed
or spilled into the unit.
3.
(Type 3)
Do not install the unit in a dusty
environment. Dust may affect/degrade the sen-
sor’s performance.
User Cautions
Careful measures were taken in the design of this
product to ensure its quality; however, the follow-
ing cautions pertain to all users and should be fol-
lowed for safe operation.
Installation Cautions
The Installation Cautions are defined as follows:
1. The Unit is not designed for outdoor installation.
Be sure that the Host Machine contains enough
protection to avoid wet or dusty conditions when
installing it in either an indoor or open-air space.
2. Ensure that the Host Machine is designed for
daily operational access for maintenance and/or
clearing a Banknote jam.
3. Be careful not to use excessive outside pressure
on the Mounting Plate when removing the Cash
Box from the Unit.
4. Avoid exposing the Unit to direct Sunlight and/or
Incandescent Lamp illumination having a
Gradient Angle of 15 Degrees or more, and an
illumination index of 3000 Lux or less. Ensure
that the Host Machine is also designed to avoid
exposing the Banknote Insertion Slot to direct
Sunlight or Incandescent light.
Table 1-1
DBV-400 Model Number Specifications
N
o
Model: DBV- 4 * * - (*) * *
N
o
(1) (2)(3) (4) (5)
(1) Model Name
(2)
Validator Sensor
0 = Standard
1-9 = Reserved
(3)
Transport Unit
0 = Standard
1-9 = Reserved
(4)
Optional Unit (Banknote Insertion Section)
None = Standard
A-Z = Reserved
(5)
Stacker Type
SU/SD = Standard
SU = Optional Rear-Access Cash Box
*
SH = Reserved
UH = Reserved
*. The optional Rear-Access Cash Box supports SU version only.
Table 1-2
DBV-400 Type Number Specifications
N
o
Model: * * * - * * - * * *
N
o
(1)(2)(3)(4)(5)(6)(7)(8)
(1)
Cash Box Capacity
*
S = 300 notes (New Banknote)
M = 500 notes (New Banknote)
L= 1000 notes (New Banknote)
*. The number of stacked Notes depends on the Banknote’s condition.
(2)
Cash Box Type
0 = Standard
1 = Optional Rear-Access Cash Box
2 - 9 = Reserved
(3)
Cash Box Door
0 = Standard
1 - 9 = Reserved
(4)
Bezel (Option)
0 = JCM Standard Bezel (Standard)
1 = Snack Mask
2 = TOB
3 = Euro Bezel
4 = Compatible Type Bezel
5 = Snack Mask (Green)
6 - 9 = Reserved
A - Z = Reserved
(5)
Centering Guide Chip Type
0 = 66mm
1 = Reserved
2 = 72mm
3 - 9 = Reserved
(6)
Optional Coating
0 = None (Standard)
1 - 9 = Reserved
(7)
Optional Board
0 = None (Standard)
1 - 9 = Reserved
(8)
Interface
0 = None (Standard)
1 = Standard Harness
2 = USB Interface Harness
3 - 9 = Reserved
Table 1-3
DBV-400 Software Number
Specifications
N
o
Software: DBV-400-* * * * * - * * * - V * .* * - * *
N
o
(A) (B) (C) (D)
(A) Software Model Name
(B) Denomination (Country Code)
*
*. The Country Code is indicated following the ISO 3166 Standard.
(C) Interface Protocol Name
(D) Software Version
Type 1 Type 2 Type 3
Figure 1-2
Precautionary Symbols
