background image

Issue #4119-IGE-01-00

© 2020, JAPAN CASH MACHINE CO., LTD.

1 2

Section 5

RBA-40C™ Banknote Acceptor

Preventive Maintenance

This

 

section provides the preventive maintenance 

for the RBA-40C™ Banknote Acceptor (RBA-

40C). It includes the following information:

•  

Clearing a Banknote Jam

•  

Opening the Centering Mechanism

•  

Cleaning Procedures

Clearing a Banknote Jam

To retrieve a jammed Banknote located inside the 

Banknote Acceptor, proceed as follows:

1.  Press on to the Upper Guide Open/Close Button 

(Figure 6 

a

) located on both sides of the RBA-

40C Unit to open the Upper Guide (Figure 6 

b

).

2.  Remove the jammed Banknote (Figure 6 

c

). 

Opening the Centering Mechanism

If a Banknote jam occurs in the Banknote Acceptor 

when the Centering Mechanism is closed, the 

Upper Guide will not open. To release (open) the

Upper Guide, power cycle the Unit and allow it to 

reset. 

Cleaning Procedures

To clean the RBA-40C Unit, gently rub the Sen-

sors, Rollers or Belts using a dry, soft, 

lint-free, Micro-fiber Cloth ONLY. 

1.  Remove electrical power.
2.  Press on to the Upper Guide Open/Close Button 

to open the Upper Guide.

3.  Clean the appropriate path and Lens of each Sen-

sor, Roller and Belt. (Refer to “RBA-40C Sen-

sors and Cleaning Locations” on page 13 for each 

Sensor and Roller that requires cleaning). 

5

PREVENTIVE MAINTENANCE

Figure 6 

Clearing a Banknote Jam

Figure 6 

Clearing a Banknote Jam

a

b

c

NOTE: If power cycling fails to clear the 

Banknote jam, use a 5.5mm nut driver to 

rotate the Centering Guide Open Shaft, then 

open the Upper Guide and remove the 

Banknote from the RBA-40C unit (Figure 7).

Figure 7 

Opening the Centering Mechanism

Figure 7 

Opening the Centering Mechanism

5.5mm Nut Driver 

Centering Guide Open Shaft 

To keep the RBA-40C Unit’s 

performance optimal, perform routine 

cleaning and maintenance;

•  

At least once a month; and/or

•  

Whenever Sensors, Rollers, Belts or 

Banknote Path are dirty due to dust, foreign 

objects or similar debris adhering to them.

Caution: Do not use alcohol, thinner or 

citrus based products for cleaning any 

Sensors or surfaces. The lenses can 

become clouded by chemical 

evaporation residue that may cause 

acceptance errors.

Caution: Do not inject water or liquid 
agents of any kind into the Acceptor, as 
this may cause extreme damage to the 
Unit.

Caution: Be sure to use non-flammable 

compressed air only.

Figure 8 

General Cleaning Image

Lens

Roller

Dry Lint-free Cloth/Cotton Swab/

Before

Cleaning

After

Cleaning

Belt

Non-flammable Air Jet

Figure 8 

General Cleaning Image

Summary of Contents for RBA-40C













































Reviews: